manualshive.com logo in svg

Honeywell KromSchroder IC 40, Technical Information, Page: 10 / 72

Share
Download
Honeywell KromSchroder IC 40 Technical Information Download Page 10

IC 40 · Edition 07.18

10

Application

1 .1 .6 Hot-air compensation

GIK

IC 40 + 

BVH

WPS

Two

point

M

VAG +VAS 1

VAS

For processes in which preheated combustion air at a 
temperature of up to 450°C must be controlled. In this 

example, the actuator IC 40 is controlled by a two-point 
controller to adjust the burner capacity. It runs in High/

Low intermittent mode. The running time can be ad-
justed between 5 and 25 seconds.

1 .1 .7 Staged control with online adjustment of the burner 

capacity

IC 40 + BVA 

BVA 

4–20 mA

VAG +VAS 1

VAS

PLC

M

For processes that require a homogeneous tempera-
ture distribution and high temperature accuracy in the 
furnace.
If only a low heat output is required, for example to 
maintain the temperature in the furnace, the burner can 

continue to be operated in intermittent mode. The ad-
justment angle of the valve is reduced via the analogue 
input (4 – 20 mA) of the actuator and the burner capac-
ity is therefore lowered. This ensures uniform tempera-

ture distribution even with a low heat output.

This function of the actuator IC 40 can also be used in 

the ceramics industry to correct the lambda value or for 
temperature compensation purposes in hot-air applica-
tions.

Summary of Contents for KromSchroder IC 40









































































Reviews:

No comments