Honeywell KromSchroder IC 40 Technical Information Download Page 12 | Manualshive

Page: 12 / 72

Honeywell KromSchroder IC 40 Technical Information Download Page 12

IC 40 · Edition 07.18

12

Function

3 Function

The actuator IC 40 moves the butterfly valve towards 0°

or 90°. There are 4 possible positions which the actua-
tor can approach in steps. Any intermediate position is
possible in continuous three-point step mode. Option-
ally, the actuator can also approach any intermediate
position via an additional current input.

The slow flashing blue LED indicates that the motor of

actuator IC 40 is moving. The position indicator on the
housing indicates the opening angle. Further visualiza-
tion and operation are performed on a PC using the
BCSoft software.

BCSoft

The sequence of opening and closing is programmed

using the BCSoft software and can be adapted indi-
vidually to any application.

All settings for the actuator IC 40 are made using
BCSoft. Commissioning and calibration of the “closed”

position are performed conveniently using the software.
BCSoft offers the option of moving and adjusting the
butterfly valve in Manual mode via the actuator, see
page 51 (Manual mode).

A detailed manual is available for the BCSoft PC soft-

ware:

www.docuthek.com

Elster Thermal Solu-

03 Valves and butterfly valves

«
...
10
11
12
13
14
...
»

Summary of Contents for KromSchroder IC 40









































































Reviews:

No comments