manualshive.com logo in svg

Honeywell KromSchroder IC 40, Technical Information, Page: 38 / 72

Share
Download
Honeywell KromSchroder IC 40 Technical Information Download Page 38

IC 40 · Edition 07.18

38

analogue

chart 2

analogue

chart 1

t [s]

high

low

closed

DI 1

DI 2

t [s]

t

1

 

t

2

Function

3 .6 .5 2-point operation with characteristic curve 

switchover I

Operating mode 25
In idle state (DI 1 and DI 2 with no signal), the actua-
tor is in “low” position (“low” position may also be 0° = 

“closed” position). 

DI 1 functions as a pulse input. The analogue char-
acteristic curve (analogue chart 1/analogue chart 2) 
is switched over via DI 2 and the adjustment angle for 
the “open” position is preset by this. This angle is ap-
proached with signal at DI 1. 
DI 2 with no signal: 

The actuator operates in analogue chart 1/low (ana-

logue chart 1/closed) intermittent mode via digital in-
put DI 1.

Signal at DI 2: 

The actuator operates in analogue chart 2/low (ana-

logue chart 2/closed) intermittent mode via digital 
input DI 1.

This function allows the actuator to switch over its in-

termittent mode in ongoing operation. The adjustment 
angle for the “open” position is preset via two charac-
teristic curves (charts), each with 5 interpolation points, 
see page 48 (Inputs). This allows the same current 
signal to be used for running through two different ca-
pacity ranges, for example for lambda adjustment or for 
hot-air compensation. 

Operating mode 25

▼

Summary of Contents for KromSchroder IC 40









































































Reviews:

No comments