manualshive.com logo in svg

Honeywell KromSchroder IC 40, Technical Information, Page: 6 / 72

Share
Download
Honeywell KromSchroder IC 40 Technical Information Download Page 6

IC 40 · Edition 07.18

6

Application

1 .1 Examples of application

1 .1 .1 Staged control

IC 40 + BVA 

BVA 

VAG + VAS 1

M

Two-

point 

step

For processes that require a homogeneous tempera-
ture distribution in the furnace. The actuator IC 40 is 

controlled by a two-point controller and operates in  

On/Off or High/Low intermittent mode. The actuator 

closes when the voltage supply is interrupted. The run-
ning time can be infinitely adjusted between 5 and 25 
seconds.

1 .1 .2 Staged control with three burner capacity levels

IC 40 + BVA

BVA

VAG + VAS 1

M

PLC

For processes that require a homogeneous tempera-
ture distribution in the furnace and three burner capac-
ity levels. The actuator IC 40 is controlled by a program-
mable logic controller and works in High/Medium/Low 

or High/Medium/Low/Off intermittent mode. This al-
lows the ignition stage to be started. The optional pres-
sure switch provides fail-safe monitoring of the maxi-
mum pilot air volume. The actuator running time can be 
infinitely adjusted between 5 and 50 (75) seconds.

Summary of Contents for KromSchroder IC 40









































































Reviews:

No comments