manualshive.com logo in svg

Honeywell KromSchroder IC 40, Technical Information, Page: 52 / 72

Share
Download
Honeywell KromSchroder IC 40 Technical Information Download Page 52

IC 40 · Edition 07.18

52

Function

3 .11 Statistics

The statistical data stored in the unit, such as fault sig-

nals which have occurred, various counter readings and 
measured values, is displayed in statistics in BCSoft.

The 

counters

 and 

measured

 

values

 ranges are each 

split into overall data and customer data. The customer 
data is used for recording information over a specific 
period.

3 .11 .1 Counters

Actuating cycles (0 – 100 – 0%), changes of direction 

(Open/Close), switching of the output relays, “Power 
On” switching operations and mains operating hours 
are added in the statistics. Besides the total counters, 
there are customer counters for recording information 
over a specific period.

3 .11 .2 Measured values

The minimum and maximum internal housing tempera-

tures are saved in statistics. In addition, the current in-
ternal temperature is displayed. Here as well, there is a 
customer memory for viewing a period.

3 .11 .3 Resetting statistics

All signals and customer data can be reset. The reset 

date is saved automatically and displayed together with 
the customer data.

Total counter and measured values cannot be reset or 

deleted.

3 .11 .4 Resetting a signal

A fault signal is signalled by the red LED on the actuator. 

The detailed cause of the signal is displayed in BCSoft. 
The cause must be remedied. The signal can then be 

acknowledged and reset with BCSoft.

Summary of Contents for KromSchroder IC 40









































































Reviews:

No comments