background image

10

NOTE:  This  accessory  must  be  used  for  all
installations  where  the  closing  force  as  measured
on the bottom of the door is over 400 N (40 kgf).

After  the  opener  has  been  installed  and  adjusted,
obstruction  detection  beams accessory  can  be
installed. Instructions are included with this accessory.

The  obstruction  detection  beams  provides  an
additional  measure  of  safety  against  a  small  child
or animal being trapped under a garage door. 
It uses
an  infra-red  beam,  which  when  broken  by  an
obstruction,  causes  a  closing  door  to  open  and
prevents  an  open  door  from  closing  and  is  strongly
recommended  for  homeowners  with  young
children.

Quick-Connect Terminals

C.  To insert or release 
     wire, push in tab with 
     screwdriver tip

A.  Strip wire 
     (11 mm)

B.  Twist like coloured 
     wires together

Red

Grey White

7/16" (11 mm)

1

2

V

 D

C

MR850EVO ONLY

16   

SAFETY FIRST!

Whilst  HomEntry  have  engineered  safety  features  into  your  garage  door  opener,  we  urge  you  to  consider  fitting
obstruction detection beams to your new garage door opener. In many countries these devices are compulsory to
assist in preventing serious injury or property damage. For your own peace of mind and the safety of others please
install this inexpensive safety device.

Door may operate unexpectedly, therefore do not allow anything to stay in the path of the door.

INSTALLING OBSTRUCTION DETECTION BEAMS   (OPTIONAL)

Timer to close feature (TTC)

TIMER TO CLOSE feature: (TTC) 10 to 180 seconds.

NOTE: Obstruction detection beams must be installed before TTC will operate.

The Timer to Close feature allows the door to automatically close after a specified time period. During the 

OPEN door waiting period, the courtesy light will flash for continuously.

If the door encounters an obstruction while closing, the opener will

return to the OPEN position and the waiting period will begin again.

To activate the Timer to Close

• Start with IRs installed and the door fully CLOSED. 

• Press and Hold both “P” and “DN” buttons for 3 seconds. When the 

Courtesy light flashes “TWICE”, release both buttons.

• Press the “UP” for each 10 second interval required for 

Timer to Close. A “BEEP” will register  for each press. “DN” button 

will reduce the count if needed.

• Press and release the “P” button to accept this setting.

To Deactivate the Timer to Close. 

• Start with the door fully CLOSED. 

• Press  and  Hold  both  “P”  and  “DN”  buttons  for  3  seconds.  When  the

Courtesy light flashes “TWICE”,  release both buttons.

• Press and release the “P” button to accept this setting. 

Auto close is NOT recommended for households with young children.

DN UP P S

1

2

3

132A2940

Flash

x 2

ACTIVATE
TIMER TO
CLOSE

SET
TIME

ACCEPT
SETTING

Flash x 2

BEEP

DN

DN

UP

UP

P

P

S

S

1

1

2

2

3

3

BEEP

DN

DN

UP

UP

P

P

S

S

1

1

2

2

3

3

Flash x 2

BEEP

DN

DN

UP

UP

P

P

S

S

1

1

2

2

3

3

ENABLING The obstruction detection beams:
• Connect the obstruction detection beam wiring to the opener and turn ON.  (The obstruction detection
beams will automatically enable once they are connected and will now operate in a FAIL SAFE mode.)

DISENABLING The obstruction detection beams: 
If the obstruction detection beams are installed and needs to be removed the opener will need to be
reprogrammed.
Perform the power ON/OFF sequence as follows.
• Remove the obstruction detection beam wires from the opener.
• Turn the mains power OFF for 5 seconds.
• Turn the power ON for 5 seconds.
• Turn the power OFF for 5 seconds.
• Turn the power ON and check the opener operates OK without the obstruction detection beams.

Summary of Contents for HERDO1





















Reviews: