background image

The complete Installation Instructions and Owner’s Manual are available at no 

charge from:
- Your local Wayne Dalton Sales Center, or
- Online at 

www.Wayne-Dalton.com

, or

- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box 

67, Mt. Hope, OH., 44660

©Copyright 2021

REV11_01/06/2021

Part Number

T a b l e   O f   C o n t e n t s

347777

PLEASE DO NOT RETURN THIS PRODUCT 

TO THE STORE

If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the 
prompts to contact a customer service 
representative. They will be happy to handle 
any questions that you may have.

Pre-Installation 

2

Important Safety Instructions 

2

Removing an Existing Door and Preparing the Opening 

2

Breakdown Of Parts 

3

Door Installation Instructions 

4

Counterbalance Installation Instructions 

7

Maintenance 

13

Cleaning Your Garage Door 

13

Painting Your Garage Door 

14

Maintaining The Finish On Your Garage Door 

14

Operation And Maintenance 

14

Warranty 

15

Wayne Dalton, a division of Overhead Door Corporation

Model 44, Double 

Flush

T

O R S I O N

Q

UICK

 S

TART

 G

UIDE

R

ESIDENTIAL

 

AND

 L

IGHT

 C

OMMERCIAL

 

R

EAR

 M

OUNT

 L

OW

 H

EADROOM

 

O

UTSIDE

 H

OOKUP

DEFINITION OF LIGHT COMMERCIAL:

1. Door Heights less than or equal to 8’0” (< = 8’0”) are considered 
Residential Applications.
2. Door Heights greater than 8’0” (> 8’0”) are considered Light 
Commercial Applications.

This 

Quick Start Guide is only meant to be used as an aid

 and 

/ or introduction to garage door installation, and does not replace the 
complete Installation Instructions and Owner’s manual available on the 
web at 

www.Wayne-Dalton.com

. Wayne Dalton highly recommends 

that you read and fully understand the Installation Instructions and 
Owner’s Manual before you attempt this installation.

To avoid possible injury, read and fully understand the enclosed 
instructions carefully before installing and operating the garage door. Pay 
close attention to all warnings and notes. After installation is complete, 
fasten this manual near garage door for easy reference.

QUICK START GUIDE IMPORTANT NOTICES!

Summary of Contents for 44 Double Flush

















Reviews: