manualshive.com logo in svg

Home Master GDR02, Operator'S Manual, Page: 41 / 47

Share
Download
Home Master GDR02 Operator'S Manual Download Page 41

38 

1/2 HP Chain Drive Garage Door Opener

 

 

Homelink

 

Accessories 

If you would like additional information on the HomeLink® Wireless Control System, HomeLink compatible products, 

programming instructions for other devices or to purchase accessories, please contact HomeLink at 

1-800-355-3515 or visit their website at www.homelink.com. 

Precautions! 

Do not use the HomeLink® Wireless Control System with any garage door opener that lacks the safety stop and 

reverse feature as required by federal safety standards. (This includes any garage door opener model 

manufactured before April 1, 1982). A garage door opener that cannot detect an object, signaling the door to stop 

and reverse, does not meet current federal safety standards. Using a garage door opener without these features 

increases risk of serious injury or death.    For more information, call 1-800-355-3515 or visit their website at 

www.homelink.com. 

This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device 

may not cause harmful interference, and (2) This device must accept any interference that may be received 

including interference that may cause undesired operation. WARNING: The transmitter has been tested and 

complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the device. 

The term “IC:” before the certification/registration number only signifies that Industry Canada technical specifications 

were met. 

IC: 279B-xxxxx JCI MODEL/FCC ID: CB2XXXXX 

HomeLink and the HomeLink house are registered trademarks of Johnson Controls, Inc. 

Summary of Contents for GDR02
















































Reviews:

No comments