Home Master GDR02 Operator'S Manual Download Page 37 | Manualshive

Page: 37 / 47

Home Master GDR02 Operator'S Manual Download Page 37

34

1/2 HP Chain Drive Garage Door Opener

Adding a New Code

Using the "Learn" Button on the Garage Door Opener

1. Press and release the “learn” button on motor unit. The learn indicator light and warning light will glow

steadily for 30 seconds

2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad.

Then press and hold the ENTER button for 3 seconds.

3. The learn indicator light will flash rapidly and the warning light will flash 3 times. Your Wireless Keypad

has now learned the code.

4. Test by pressing the new PIN, then press Enter. The garage door opener should operate.

To Change an Existing Code

If the existing code is known, it may be changed by using the Keyless Entry.

1. Enter the four buttons for the present PIN, then press and hold the # button. The warning light will glow

steadily. Release the # button.

2. Within 15 seconds, press the new 4-digit code you have chosen, then press and hold Enter for 3

seconds. The warning light will blink twice, then blink rapidly and stop. The new code is now
programmed.

3. Test by pressing the new PIN, then press Enter. The garage door opener should operate.

To Add a Guest Entry (Temporary) PIN

A Guest Entry PIN can be added to your Keyless Entry Pad which allows you to authorize access by visitors or service
people by addiding a temporary 4 digit PIN.

1. Press the 4 buttons for your personal entry Master PIN, then press and hold the * button until the warning light

stays on.

2. Within 15 seconds, press the 4 buttons for your personal Guest Entry PIN (can not set as 0000), then press

and hold the ENTER button.

3. The warning light will blink twice when the Guest Entry PIN has been added successfully. If you input an

incorrect code more than ten times continuously, the Keyless Entry Pad would stop working for fifteen minutes.
During the fifteen-minute pause, the warning light will blink consistently. However, you can use the Hand-Held
Remote or the Control Console to recall the Keyless Entry to work.

To Erase a Guest Entry (Temporary) PIN

1. Press the 4 buttons for your personal entry Master PIN, then press and hold the * button until the warning light

stays on.

2. Within 15 seconds, enter 0000, press and hold the ENTER button.

3. The warning light will blink twice when the Guest Entry PIN has been erased successfully.

«
...
35
36
37
38
39
...
»

Summary of Contents for GDR02
















































Reviews:

No comments