manualshive.com logo in svg

Home Master GDR02, Operator'S Manual, Page: 36 / 47

Share
Download
Home Master GDR02 Operator'S Manual Download Page 36

33 

1/2 HP Chain Drive Garage Door Opener

 

 

Learn Button Indicator Light 

Programming the Remote Controls 

Your garage door opener has already been programmed at the factory to operate with your hand-held remote control. 

The door will open and close when you press the first push button. 

Below are instructions for programming your opener to operate with additional remote controls. 

Programming Remote Control   

Using the "Learn" Button on the Garage Door Opener 

1.  Press and release the “learn” button on the motor unit. The learn indicator light and warning light will glow 

steadily for 30 seconds. 

 

2.  Within 30 seconds, press all three push buttons on the remote control then release the buttons. 

Note

: 

learn indicator light will flash slowly. 

3.  Within 30 seconds, press and hold the button on the handheld remote that you wish to operate your 

garage door for 3 seconds and release. 

Note

: Learn indicator light will blink rapidly and stop. 

Erasing All Codes From Garage Door Opener M emory 

To deactivate any unwanted remotes, first erase all codes. Push the Learn button and hold for approximately 6 seconds. 
All previous codes are now erased.   

Reprogram each remote or Keyless entry you wish to use. 

Adding or Changing a Keyless Entry Code   

The keyless entry control panel and garage door opener must be programmed with a code in order to operate your 

garage door opener with the keyless entry. 

Learn 

Button

Summary of Contents for GDR02
















































Reviews:

No comments