Holman DIAL EZY GARDENER Instruction Manual Download Page 26 | Manualshive

Page: 26 / 36

background image

24

INSTALLATION INSTRUCTIONS

Pump Start Relay Connection (Water supply by pump system)

This controller does not provide mains power to drive a pump. A pump must be driven

via an external relay and contactor setup as detailed below. The controller provides

a low voltage signal that actuates the relay which in turn enables the contactor and

finally the pump.

HINT: Although the controller has permanent memory and thus a default program

will not cause erroneous valve actuation as in some controllers, it is still good

practice when using a system where the water supply comes from a pump to

connect unused stations on the unit back to the last used station. This in effect,

inhibits the chances of the pump ever running against a closed head.

Single Phase Pump Installation

Link any unused

stations to the

last active station.

Note:

It is recommended to always use a relay between the controller and the pump

starter.

«
...
24
25
26
27
28
...
»

Summary of Contents for DIAL EZY GARDENER





































Reviews:

No comments

Related manuals for DIAL EZY GARDENER

Brand: iGuzzini Pages: 20

Brand: GE Pages: 2

Druck DPI 620 Genii

Brand: GE Pages: 154

Arize Element Top Light

Brand: GE Pages: 2

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 166

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 340

Brand: Raytheon Pages: 68

Brand: Hands Free Farm Pages: 24

Nebula Blizzard v3

Brand: Lanta Pages: 8

Brand: Kalco Lighting Pages: 6

Brand: AS MOTOR Pages: 36

Powerator 1800 compact

Brand: Seto Pages: 39

Brand: Veeder-Root Pages: 58

IKN18 IPX4 PROFESSIONAL Lampion

Brand: N'oveen Pages: 8

Brand: Green-Qube Pages: 4

GR-292/M/HL/ADR

Brand: olympia electronics Pages: 8

Brand: UCHIDA Pages: 113

Brand: Eaton Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands