Holiday Trip 2012, Owner'S Manual

Page: 66 / 242

61
In
te
rio
r &
E
xt
er
io
r C
ar
e -
3
2012 Trip
Restoring the clear finish:
The finished surface on the wood is a clear
lacquer coating. The lacquer finish can be
repaired should the finish become dulled or
scratched. Scratches extending into the wood
will require wood repair by filling the damaged
area. If there is light damage, the wood can be
steamed to bring the wood surface level.
Lacquer finish sheen can be restored by
carefully using 0000 steel wool or equivalent.
Sand damaged lacquer with fine sandpaper.
Once the scratched surface is smooth, apply
a clear lacquer coating using an aerosol.
Lacquer can be applied by cloth or brush, but
best results are obtained from an aerosol. If
necessary, use 0000 steel wool or equivalent to
bring out the luster and smooth overspray.
CAUTION:
Use top coats and finishes in
accordance with the manufacturer’s
safety instructions. Use only in
well ventilated areas with proper
respiratory filters and masks.
Re-staining the wood:
If bare wood is visible at the bottom of the
scratch, the wood will need to be re-stained.
To remove damaged varnish, lightly roughen a
small area around the scratch with sandpaper,
steel wool or synthetic steel wool. Find a stain
that is a shade lighter than the wood finish.
Stain the bare wood with a very small amount
of stain on a rag, brush or cotton swab. If the
color is too light, apply additional coats. Rub
away excess stain with a dry rag. If the wood
becomes too dark, use a rag moistened in
mineral spirits to lighten the wood. Select a
lighter color stain and continue.
Several companies have simplified this repair
process by designing oil-based wood stain into
marker-like containers to rub on the scratch.
Torn and scratched wood fibers will absorb
stain and darken quickly. Start with a stain
color that is lighter than the original finish. A
second coat can always be applied if the color
of the first coat is too light. Once the color is
blended, patch the clear finish as described
above and apply a wipe-on finish.
coUntertopS
Solid Surface
Routine Care:
The solid surface countertops have a matte/
satin finish. Soapy water or ammonia-based
cleaners will remove most dirt and stains from
all tops and bowls. Individual techniques may
be used to remove different stains. Follow the
recommendations below.
Cleaning the Countertops:
Most dirt and stains: Use soapy water or
ammonia-based cleaner.
Water marks: Wipe with damp cloth and
towel dry.
Difficult stains: Use Soft Scrub ® and a
gray Scotchbrite ® pad. If Scotchbrite is used,
buffing may be necessary to restore finish.
Disinfecting: Occasionally wipe surface
with diluted household bleach (one part water
and one part bleach).
Repairing Cuts and Scratches
Solid surface countertops are renewable. Use
the following instructions to repair minor cuts
and scratches:
If scratch or imperfection is deep,
sand area with highest grit sandpaper
to remove the blemish. Never sand in
one small area. Feather out lightly at
each increase in sandpaper grit to blend
restoration.
Switch from sandpaper to 3M ™ # 35
Trizact ™ microabrasive disc. Apply
water while using Trizact discs to
prevent clogging.
Work downward to #10 Trizact
microabrasive disc until blemish is
gone.
Buff surface with wool pad and
3M Imperial Compound and Finish
Material.
NOTE:
Do not cut directly on the solid
surface.
Preventing Heat Damage:
Hot pans and heat-generating appliances,
such as frying pans or crock pots, can damage
the surface. To prevent heat damage, always
use a hot pad or a trivet with rubber feet to
protect the surface.
Other Important Tips:
Avoid exposing the solid surface to
chemicals such as paint removers or oven
cleaners. If these chemicals come in contact
with the solid surface, quickly wash with
water. Avoid contact with nail polish or nail
polish remover. If contact is made, quickly
wash with water.
CAUTION:
Do not cut directly on the solid
surface.



