Holemaker Technology VERSADRIVE V60T Original Instructions Manual Download Page 22 | Manualshive

Page: 22 / 48

background image

22

V60T/July 2020/V1.1

5.2

Control panel

The control panel on your magnetic drilling machine is designed for maximum operating safety.

1.

Magnet Switch (Illuminated)

2.

Motor NVR Switch

3.

Spindle Direction Switch

4.

Magnet Protection Fuse (2A Fast Blow)

[image 13]

5.2.1

Magnet Switch

The magnet switch (Image 13 - item 1) is an illuminated rocker switch.
When in the on position the switch will illuminate red.
This switch provides power to the electro magnet base.

The magnet switch must be turned on as soon as the machine is in position, before any attempt to
use the drill is made.

The magnet switch also supplies power for the motor to operate, if it is off the motor will not start.

«
...
20
21
22
23
24
...
»

Summary of Contents for VERSADRIVE V60T

















































Reviews:

No comments

Related manuals for VERSADRIVE V60T

Brand: Patio Chef Pages: 34

Brand: Kay Home Products Pages: 6

Brand: Heston Blumenthal Pages: 92

Brand: Waldorf Pages: 22

Brand: Weber Pages: 72

Brand: Metabo Pages: 64

Brand: Nostalgia Electrics Pages: 30

Brand: EFBE-SCHOTT Pages: 16

Brand: STEELE PRODUCTS Pages: 9

S 131 LAS TAPAS

Brand: White and Brown Pages: 20

MASTER-TOUCH 14501001

Brand: Weber Pages: 20

Brand: BorMann Pages: 73

Feed Life ZPG-700E Series

Brand: Z GRILLS Pages: 21

Brand: Parkside Pages: 55

Brand: Fiesta Pages: 12

Brand: Kingsford Pages: 22

Brand: SEVERIN Pages: 92

Brand: Ozito Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands