HOKLARTHERM Riga 2 S/2 Assembly Instructions Manual Download Page 3 | Manualshive

Page: 3 / 20

background image

3

Getting Started

:

1) The assembly has to be executed by at least two people - a 3rd person to
help out from time-to-time is recommended!

2) W ork cautiously, with the proper tools. Make sure that the stepladder’s footing
is secure!

3) W e recommend that you work with gloves (although all of the edges have
been filed, it is always possible for you to be cut when handling either the
aluminum or polycarbonate parts).

4) You need the following tools for the assembly:

1 pc  Phillips-head Screwdriver for recessed-head screws, siz e # 2
1 pc  O pen-jaw wrench, 10 mm (0.4”)
1 pc  Screwdriver for slotted screws
1 pc  W ater level
1 pc  Step L adder, approx. 6-feet high
1 pc  File to remove possible sharp edges
1 pc  Rubber Mallet
1 pc  Measuring Tape
1 pc  E lectric or Cordless D rill
1 pc  Bungee Cord
1 pc  Caulking Gun

IN D E X

Part L ist:

Pages 4 & 5

Main Frame Assembly:

Pages 6 - 11

Foundation Fram Assembly:

Page 10

Roof W indow Assembly:

Page 12

Rear W indow Assembly:

Page 13

Front D oor Assemble:

Pages 14 & 15

Mounting Accessories:

Pages 16 & 17

Inserting Rubber Seals:

Page 17

Assembling O ptional Shelves:

Pages 18 & 19

Care & Maintenance:

Page 20

Costume Service:

Page 20

«
1
2
3
4
5
...
»

Summary of Contents for Riga 2 S/2





















Reviews:

No comments

Related manuals for Riga 2 S/2

Brand: Vitavia Pages: 28

Brand: MyFood Pages: 52

Brand: Palram Pages: 61

Brand: Quictent Pages: 36

TALL FLOWERBED 2400 x 1060 x 800

Brand: Transform Pages: 2

Brand: Costway Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands