background image

- 6 -

SAFETY PRECAUTIONS

Disposal of an old air conditioner

Before disposing an old air conditioner, please 

make  sure  it  is  inoperative  and  carry  out  the 

disposal  by  adopting  all  safety  precautions. 

Unplug it from the power line in order to avoid 

risks of electric shock.
Please  remember  that  an  air  conditioner 

contains refrigerant fluid, requiring specialized 

waste disposal. 
The  valuable  materials  contained  in  the  air 

conditioner can be recycled. Contact your local 

Waste Disposal Center for adequate disposal or 

contact your Dealer for any question.
Please  make  sure  that  piping  of  your  air 

conditioner  does  not  get  damaged  before 

being picked up by the relevant Waste Disposal 

Center. You can contribute to the protection of 

the  environment  by  adopting  an  appropriate 

anti-pollution method of disposal.

Disposal of the packaging of your new air 

conditioner

All the packaging materials used in the package 

of  your  new  air  conditioner  can  be  disposed 

without any danger for the environment.
The cardboard may be broken or cut into small 

pieces  and  given  to  a  Waste  Paper  Disposal 

Service. The wrapping bag made of polyethylene 

and  the  polyethylene  goam  pads  contain  no 

fluorochloric hydrocarbon.
All these valuable materials may be taken to a 

Waste Collecting Center and used again after 

adequate recycling.
Consult  your  local Authorities  for  the  name 

and address of the Waste Materials Collecting 

Centers  and  Waste  Paper  Disposal  Services 

nearest to your house.

General warnings for safety

• Do not operate damaged air conditioners. In case of doubt, contact your Dealer.
• Use of air conditioner must be carried out in strict compliance with the instructions listed futher 

on.

• Do not damage any parts of the air conditioner that carry refrigerant by piercing or perforating the 

piping with sharp or pointed objects, by crushing or twisting the tubes or scraping off the surfaces' 

coatings. If the refrigerant spurts out and gets into eyes, this may result in serious injuries.
• Do not obstruct or cover the ventilation grille of the air conditioner. Do not put fingers nor insert 

objects into the inlet/outlet vent or into the motorized louver.
• Do not allow children to play with the air conditioner. Children should be never allowed to sit on 

the Oudoor Unit.

• The appliance is not intended for children and disabled people. They must not operate the air 

conditioner without supervision.
• Electrical works must be carried out according to the local laws. If the power cable is damaged, it 

must be replaced by the Manufacturer or by qualified Personnel. Size of power cables and connecting 

wires must be adequate to the characteristics of the air conditioner (current values and power input 

values).
• If fuses on the PCB are blown, they must be replaced with new fuses of the same type and size.
• After installation, power plug should be properly disposed.
• Exhausted batteries (infrared remote controller) should be properly disposed.
• Always remember to unplug the air conditioner before opening the inlet grille. Never try to unplug 

the air conditioner by pulling off the power cable. Always grip the power plug firmly and pull it straight 

out of the power socket.

Before starting the air conditioner, please read carefully the information in this "USER'S MANUAL". 

The User's Manual contains very important suggestions relatied to installation, operation and 

maintenance of the air conditioner and concerning your personal safety.

The Manufacturer accept no responsibility for the damages that may arise due to non-

observance of the instructions listed in this "USER'S MANUAL".

Summary of Contents for HCND 261 X









































Reviews: