HKS 12001-AT005 Installation Manual Download Page 80

Page: 80 / 81

HKS GT SUPERCHARGER SYSTEM /LS460

- 79 -

22. MAINTENANCE

○

Traction Oil is used specifically for the HKS GT Supercharger. Do not use other types of oils; use of

other brands of Traction Oil, engine oil, or transmission oil can lead to damage to the HKS GT
Supercharger internals.

○

Use the part number below to order Traction Oil.

○

Replace the Traction Oil Filter every 5 years or 70,000km after installing the HKS GT Supercharger.
- Use the part number below to order the Traction Oil Filter.

○

Belts are consumable parts. Always check belts prior to driving for any cracks or tears.

Replace damaged belts immediately.

Use the part number below to order the Ribbed Belt.

・

Traction Oil does not need to be replaced, however check oil level prior to driving. If oil

level is low, add Traction Oil as necessary.

Product Name

Part Number

Traction Fluid

12002-AK029

Product Name

Part Number

Traction Fluid Filter

12002-AK015

Product Name

Part Number

Belt 7PK1030

G13572-T63010-00

Belt 6PK2135

G13572-T63020-00

CAUTION

Summary of Contents for 12001-AT005


















































































Search results

Summary of Contents for 12001-AT005

Reviews:

Related manuals for 12001-AT005

Brands by name

Popular brands

HKS 12001-AT005, Installation Manual

Search results

Summary of Contents for 12001-AT005

Reviews:

Related manuals for 12001-AT005

Brands by name

Popular brands