HKS 12001-AT005 Installation Manual Download Page 3

Page: 3 / 81

HKS GT SUPERCHARGER SYSTEM /LS460

- 2 -

〇

Additional Required Items

INTRODUCTION



Read this manual prior to installation.



Installation must be done by a professional.



After installation, follow the instructions for safe use.



Refer to the factory service manual as well as this manual when removing factory parts during

removal and installation.

ATTENTION



This manual indicates items you need to pay attention to in order to install this product safely and

lists precautions to avoid any possible damage and/or accidents.



This product is an automobile part. Do not use for any other purposes.



HKS will not be responsible for any damage caused by incorrect installation and/or use, or use

after modification and/or dismantling of this product.



This product was designed for installation on a specific JDM

factory vehicle.



The specifications of this product are subject to change without notice.



The instructions are subject to change without notice. Make sure to refer to the most recent

instructions.

Description Remarks

Long Life Coolant

Approximately 5 liters

Exhaust Gaskets

Toyota OEM

・

17173-38030 Exhaust Manifold Head Gasket (2 pcs.)

・

90917-06078 Exhaust Pipe Gasket No.2 (2 pcs.)

・

90917-06057 Exhaust Pipe Gasket (2 pcs.)

Air Cleaner
(Recommended)

Toyota OEM cleaner must be used.
It is recommended to replace with new cleaners before installing this kit.

・

17801-38010-79 (1 pc)

Summary of Contents for 12001-AT005


















































































Search results

Summary of Contents for 12001-AT005

Reviews:

Related manuals for 12001-AT005

Brands by name

Popular brands

HKS 12001-AT005, Installation Manual

Search results

Summary of Contents for 12001-AT005

Reviews:

Related manuals for 12001-AT005

Brands by name

Popular brands