HKS 12001-AT005 Installation Manual Download Page 56

Page: 56 / 81

HKS GT SUPERCHARGER SYSTEM /LS460

- 55 -

Black/Whit

Black

Black/Red

Brown

Black/Blue

10. EXTENSION OF AIRFLOW HARNESS

The following procedure only depicts the extension of the airflow harness on the

left

bank. Repeat this

procedure for the

right

bank as well.

○

Remove the airflow harness cover.

○

Make sure the factory harness colors are as follows
(from the left viewing from the terminal insert.)

Black/Blue

→

Brown

→

Black

→

Black/White

→

Black/Red

Make a note if the color order is different.

○

Insert the compact precision screwdriver into the hole

①

, and pull out the retainer (white resin part).

○

Insert the flathead precision screwdriver into the both sides’ gap

②

. Move the screwdriver up and

down to make the gap larger. Remove the front holder.

○

Pull the lock up to release it using the precision
screwdriver. Pull the terminal out.

①

②

Make these gaps

②

larger.

Summary of Contents for 12001-AT005


















































































Search results

Summary of Contents for 12001-AT005

Reviews:

Related manuals for 12001-AT005

Brands by name

Popular brands

HKS 12001-AT005, Installation Manual

Search results

Summary of Contents for 12001-AT005

Reviews:

Related manuals for 12001-AT005

Brands by name

Popular brands