HKS 12001-AT005 Installation Manual Download Page 50

Page: 50 / 81

HKS GT SUPERCHARGER SYSTEM /LS460

- 49 -

○

Install the Pipe Bracket to the front cross member.

○

Temporarily install Inlet Pipe No.2.

・

Place the

shorter

straight portion

①

to the

intercooler side. (See the diagram below.)

○

Adjust the position of Outlet Pipe No.1 so it does not
come in contact with the harnesses from the relay box.

○

Tighten all bolts, nuts, and hose clamps temporarily
installed. Make sure all installed parts do not come in
contact with any other parts of the vehicle.

・

Pipe Bracket

（

Hole Dia.12mm

）

・

Inlet Pipe No.2

・

Silicone Hose 65mm L=70 (2 pcs.)

・

Silicone Hose 65mm L=20

・

Hose Clamp #40 (5 pcs.)

Hole Dia.

12mm

①

②

・

Install the Silicone Hose 65mm L=20 to
the pipe. Temporarily install the pipe to the
Pipe Bracket using the Hose Clamp #40.

Summary of Contents for 12001-AT005


















































































Search results

Summary of Contents for 12001-AT005

Reviews:

Related manuals for 12001-AT005

Brands by name

Popular brands

HKS 12001-AT005, Installation Manual

Search results

Summary of Contents for 12001-AT005

Reviews:

Related manuals for 12001-AT005

Brands by name

Popular brands