background image

Safety Precautions (5)

SAFETY PRECAUTIONS 

(Continued)

Ink and Makeup Handling

WARNING

 When charging a refill of ink or makeup, exchanging ink, or otherwise 

   handling ink or makeup, take enough care not to spill ink or makeup.

If you spill any ink or makeup by mistake, wipe it off neatly and promptly with 
wiping paper or something similar. Do not close the maintenance cover until 
you make sure that the portion you have just wiped is completely dry. 

   You must pay particular attention when you have spilled ink or makeup inside 

the printer and it is not completely dry. Why? Because vapors of ink or 
makeup will stay inside the printer and may catch on or cause a fire. 

If you find it hard to wipe the printer when it is turned on, stop it with the maintenance 
cover open. Power it down, and then wipe it off again. 

 If you wish to clean the casing of the printer with wiping paper impregnated 

with makeup, be sure to do so with the power off. 

Attempting to clean it when the power is on will cause makeup or vapors of makeup 
to enter the printer, possibly catching on or causing a fire. 
When the cleaning is over, open the maintenance cover and make sure that no 
makeup has entered and no vapors remain inside. 

 Should you find a leak of ink or makeup inside the printer while the printer is 

running or being maintained, wipe it off promptly with wiping paper or 

   something similar. Then, with the maintenance cover open, stop the printer, 

power it down, and repair the leak. 

Continuing operation with a leak of ink or makeup will cause an anomaly, 
resulting in abnormal printing. 
Ink and makeup are flammable. They may therefore catch on or cause a fire.

 The ink and makeup, their waste solution, used wiping papers and empty 

containers are flammable. Waste disposal must comply with appropriate 

   regulations. Consult the appropriate regulatory agency for further information.

CAUTION

 Since the ink and makeup contain organic solvents, observe the following 

handling precautions.

When handling the ink or makeup, wear protective gloves and safety goggles to 
avoid direct skin contact.  If the ink or makeup comes into contact with skin, wash 
thoroughly with soap and warm or cold water.
When transferring the ink or makeup to or from a bottle, exercise caution to 
prevent it coming into contact with the printer or surrounding articles. 
If there is any spillage, immediately wipe it clean using a cloth moistened with 
makeup.

 Ink and makeup must be stored as flammable liquids.  Storage must comply 

with local regulatory requirements.  Consult the appropriate regulatory 
agency for further information.

1

2

Summary of Contents for UX

























































































Reviews: