Hitachi HTS721010G9AT00 Specifications Download Page 95 | Manualshive

Page: 95 / 225

background image

Travelstar 7K100 Hard Disk Drive Specification

81

The password, the Set Max security mode, and the unlock counter do not persist over a power cycle but they persist
over a hardware or software reset.

NOTE:

If this command is immediately preceded by a Read Native MAX ADDRESS command, it shall be

interpreted as a Set Max ADDRESS command regardless of Feature register value.

Figure 5: Set Max security mode transition

11.11 Address Offset Feature (vendor specific)

Computer systems perform initial code loading (booting) by reading from a predefined address on a disk drive. To
allow an alternate bootable operating system to exist in a reserved area on a disk drive this feature provides a Set
Features function to temporarily offset the drive address space. The offset address space wraps around so that the
entire disk drive address space remains addressable in offset mode. The Set Max pointer is set to the end of the
reserved area to protect the data in the user area when operating in offset mode. This protection can be removed by
a Set Max Address command to move the Set Max pointer to the end of the drive. But any commands which access
sectors across the original native maximum LBA are rejected with error, even if this protection is removed by a Set
Max Address command.

11.11.1 Enable/Disable Address Offset Mode

Subcommand code 09h Enable Address Offset Mode offsets address Cylinder 0, Head 0, Sector 1, LBA 0, to the
start of the nonvolatile protected area established using the Set Max Address command. The offset condition is
cleared by Subcommand 89h Disable Address Offset Mode, Hardware reset or Power on Reset. If Reverting to
Power on Defaults has been enabled by Set Features command, it is cleared by Soft reset as well. Upon entering
offset mode the capacity of the drive returned in the Identify Device data is the size of the former protected area. A
subsequent Set Max Address command with the address returned by the Read Max Address command allows access
to the entire drive. Addresses wrap so the entire drive remains addressable.

If a nonvolatile protected area has not been established before the device receives a Set Features Enable Address
Offset Mode command, the command fails with Abort error status.

Disable Address Offset Feature removes the address offset and sets the size of the drive reported by the Identify
Device command back to the size specified in the last nonvolatile Set Max Address command.

«
...
93
94
95
96
97
...
»

Summary of Contents for HTS721010G9AT00


































































































































































































































Reviews:

No comments

Related manuals for HTS721010G9AT00

Brand: Hallowell Pages: 6

Brand: Falcon Pages: 19

Brand: Euromate Pages: 23

Brand: G-Technology Pages: 17

Brand: Chieftec Pages: 18

Brand: IBM Pages: 60

Brand: Plasmon Pages: 33

NXA-WC80211G-CF

Brand: AMX Pages: 6

2.5-Inch Mobile 5400 RPM 9.5mm Travelstar HTS547575A9E384

Brand: Hitachi Pages: 2

2.5-Inch Mobile 5400 RPM 9.5mm Travelstar HTS545050B9A300

Brand: Hitachi Pages: 2

2.5-INCH HTS543232L9A300

Brand: Hitachi Pages: 2

2.5-Inch Mobile 5400 RPM 7mm Travelstar HTS545050A7E380

Brand: Hitachi Pages: 2

Ultrastar 15K73

Brand: Hitachi Pages: 273

Travelstar 5K500

Brand: Hitachi Pages: 5

Travelstar 5K500.B

Brand: Hitachi Pages: 5

Travelstar 40GN

Brand: Hitachi Pages: 2

Travelstar 4K40

Brand: Hitachi Pages: 2

Travelstar 4K80

Brand: Hitachi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands