Hitachi HTS721010G9AT00 Specifications Download Page 216

Page: 216 / 225

Travelstar 7K100 Hard Disk Drive Specification

200

Note 1.

These commands have two command codes and appear in this table twice, once for each command code.

Note 2.

The WRITE VERIFY command implemented vendor specific. The operation is the same as WRITE SEC-

TORS and verification is not performed.

Note 3.

Protected Area Feature Set

Note 4.

Power Management Feature Set

Code

Command Name

Implementation for

Travelstar 7K100

ATA-6 Category

Type

C8h

READ DMA

Yes

Mandatory

C9h

READ DMA

Yes

Obsoleted

CAh

WRITE DMA

Yes

Mandatory

CBh

WRITE DMA

Yes

Obsoleted

CCh

WRITE DMA QUEUED

Optional

CDh

CFA WRITE MULTIPLE W/O ERASE

Optional (Note 7)

DAh

GET MEDIA STATUS

Optional (Note 7)

DEh

MEDIA LOCK

Optional (Note 7)

DFh

MEDIA UNLOCK

Optional (Note 7)

E0h

STANDBY IMMEDIATE

Yes

Mandatory

E1h

IDLE IMMEDIATE

Yes

Mandatory

E2h

STANDBY

Yes

Mandatory

E3h

IDLE

Yes

Mandatory

E4h

READ BUFFER

Yes

Optional

E5h

CHECK POWER MODE

Yes

Mandatory

E6h

SLEEP

Yes

Mandatory

E7h

FLUSH CACHE

Yes

Mandatory

E8h

WRITE BUFFER

Yes

Optional

ECh

IDENTIFY DEVICE

Yes

Mandatory

EDh

MEDIA EJECT

Optional (Note 7)

EEh

IDENTIFY DEVICE DMA

Obsoleted

EFh

SET FEATURES

Yes

Mandatory

F0h

SENSE CONDITION

Vendor specific

F1h

SECURITY SET PASSWORD

Yes

Optional (Note 6)

F2h

SECURITY UNLOCK

Yes

Optional (Note 6)

F3h

SECURITY ERASE PREPARE

Yes

Optional (Note 6)

F4h

SECURITY ERASE UNIT

Yes

Optional (Note 6)

F5h

SECURITY FREEZE LOCK

Yes

Optional (Note 6)

F6h

SECURITY DISABLE PASSWORD

Yes

Optional (Note 6)

F7h

FORMAT UNIT

Vendor specific

F8h

READ NATIVE MAX ADDRESS

Yes

Optional

F9h

SET MAX ADDRESS

Yes

Optional

FB-FFh

Vendor specific

Reserved

Vendor specific

Reserved: all remaining codes

Reserved

Summary of Contents for HTS721010G9AT00


































































































































































































































Search results

Summary of Contents for HTS721010G9AT00

Reviews:

Related manuals for HTS721010G9AT00

Brands by name

Popular brands

Hitachi HTS721010G9AT00, Specifications

Search results

Summary of Contents for HTS721010G9AT00

Reviews:

Related manuals for HTS721010G9AT00

Brands by name

Popular brands