manualshive.com logo in svg

Hitachi HTS721010G9AT00, Specifications

The Hitachi HTS721010G9AT00 is a high-performance hard drive designed for efficient data storage. To get started quickly, a comprehensive Quick Installation Manual is available for free download at manualshive.com, providing step-by-step instructions for seamless integration into your system. Install your drive with ease using this downloadable manual.

Share
Download
background image

Load/unload ....................................................................................................................26

M

Magnetic fields  ...............................................................................................................23
Mechanical positioning ...................................................................................................14
Mechanical specifications ...............................................................................................28
Mode transition time .......................................................................................................16
Mounting hole locations .................................................................................................28
Mounting orientation ......................................................................................................29

N

Non-data commands  .......................................................................................................89

O

Operating modes
description .......................................................................................................................16

P

Packaging ........................................................................................................................34
Performance characteristics ............................................................................................13
Physical cylinders  ...........................................................................................................12
PIO timings  .....................................................................................................................41
Power consumption effiency  ..........................................................................................24
Power management commands ......................................................................................70
Power management features ...........................................................................................70
Power-off considerations  ................................................................................................68
Power-Off Sequence  .......................................................................................................26
Preventive maintenance  ..................................................................................................25
Protected Area Function  .................................................................................................79

R

Radiation noise  ...............................................................................................................23
Read Buffer .....................................................................................................................118
Read DMA  ......................................................................................................................119
Read DMA EXT  .............................................................................................................121
Read Long .......................................................................................................................129
Read Native Max ADDRESS  .........................................................................................134
Read Sectors ...................................................................................................................136
Read Verify Sectors  ........................................................................................................139
Recalibrate ......................................................................................................................143

Summary of Contents for HTS721010G9AT00


































































































































































































































Reviews:

No comments

Related manuals for HTS721010G9AT00

IBM Deskstar 34GXP Quick Installation Manual preview
Deskstar 34GXP
Brand: IBM Pages: 2
IAC INDUSTRIES Quick Ship ISLES WORKMASTER Assembly Instructions Manual preview
Quick Ship ISLES WORKMASTER
Brand: IAC INDUSTRIES Pages: 11
Quantum DLT 2500 Product Manual preview
DLT 2500
Brand: Quantum Pages: 345
Elektra Beckum Universal Working Table WT 840 (German) Montageanleitung preview
Universal Working Table WT 840
Brand: Elektra Beckum Pages: 4
Premio FlacheSAN2-D5 Quick Manual preview
FlacheSAN2-D5
Brand: Premio Pages: 2
Seville Classics UltraHD 20267 Assembly Instructions Manual preview
UltraHD 20267
Brand: Seville Classics Pages: 9
Air innovations SSC4500DX Operation And Maintenance Manual preview
SSC4500DX
Brand: Air innovations Pages: 30
Seagate Barracuda 7200.10 PATA Product Manual preview
Barracuda 7200.10 PATA
Brand: Seagate Pages: 54
ABSCO SHEDS 30152GK-PTX Assembly Instructions Manual preview
30152GK-PTX
Brand: ABSCO SHEDS Pages: 21
QNAP TS-130 User Manual preview
TS-130
Brand: QNAP Pages: 39
IBM SAN768B Installation, Service And User Manual preview
SAN768B
Brand: IBM Pages: 208
Palmako Rasmus FR44-3857-5 Installation Manual preview
Rasmus FR44-3857-5
Brand: Palmako Pages: 37
BITO SDS Instructions For Assembly And Use preview
SDS
Brand: BITO Pages: 64
Cavalry CAUPT Series User Manual preview
CAUPT Series
Brand: Cavalry Pages: 16
SaniBin T640 Instruction Manual preview
T640
Brand: SaniBin Pages: 8
WELSON ES2000 Operation Manual preview
ES2000
Brand: WELSON Pages: 23
LaCie LRD0TUA User Manual preview
LRD0TUA
Brand: LaCie Pages: 25
Franklin WAS-3019 User Manual preview
WAS-3019
Brand: Franklin Pages: 24

Brands by name

Popular brands

Load more brands