manualshive.com logo in svg

Hitachi HTS721010G9AT00, Specifications

Share
Download
Hitachi HTS721010G9AT00 Specifications Download Page 215

Travelstar 7K100 Hard Disk Drive Specification

199

 

15.0  Appendix

15.1  Commands Support Coverage

The table below compares the command support coverage of the Travelstar 7K100 with the ATA-6 defined com-
mand set. The third column indicates the capability of the drive for those commands.

Code

Command Name

Implementation for 

Travelstar 7K100

ATA-6 Category 

Type

00h

NOP

No

Optional

03h

CFA REQUEST EXTENDED ERROR CODE

No

Optional (Note 7)

08h

DEVICE RESET

No

Optional (Note 7)

1xh

RECALIBRATE

Yes

Obsoleted

20h

READ SECTOR(S)

Yes

Mandatory

21h

READ SECTOR(S)

Yes

Obsoleted

24h

READ SECTOR(S) EXT

Yes

Optional

22h

READ LONG

Yes

Obsoleted

23h

READ LONG

Yes

Obsoleted

30h

WRITE SECTOR(S)

Yes

Mandatory

31h

WRITE SECTOR(S)

Yes

Obsoleted

32h

WRITE LONG

Yes

Obsoleted

33h

WRITE LONG

Yes

Obsoleted

38h

CFA TRANSLATE SECTORS W/O ERASE

No

Optional (Note 7)

3Ch

WRITE VERIFY (2)

Vendor specific

Obsoleted

40h

READ VERIFY SECTOR(S)

Yes

Mandatory

41h

READ VERIFY SECTOR(S)

Yes

Obsoleted

50h

FORMAT TRACK

Yes

Obsoleted

7xh

SEEK

Yes

Mandatory

87h

CFA TRANSLATE SECTORS

No

Optional

90h

EXECUTE DEVICE DIAGNOSTIC

Yes

Mandatory

91h

INITIALIZE DEVICE PARAMETERS

Yes

Mandatory

92h

DOWNLOAD MICROCODE

Reserved

Optional

94h-99h

Reserved

Reserved

Reserved

A0h

PACKET

No

Not to be used

A1h

IDENTIFY PACKET DEVICE

No

Not to be used

A2H

SERVICE

No

Not to be used

B0h

S.M.A.R.T. FUNCTION SET

Yes

Optional (Note 5)

C0h

CFA ERASE SECTORS

No

Optional

C4h

READ MULTIPLE

Yes

Mandatory

C5h

WRITE MULTIPLE

Yes

Mandatory

C6h

SET MULTIPLE MODE

Yes

Mandatory

C7h

READ DMA QUEUED

No

Optional

Summary of Contents for HTS721010G9AT00


































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands