Hitachi HTS721010G9AT00 Specifications Download Page 165 | Manualshive

Page: 165 / 225

background image

Travelstar 7K100 Hard Disk Drive Specification

151

Security Level

A zero indicates a High level, a one indicates a Maximum level. If the host sets the High level and the password is
forgotten then the Master Password can be used to unlock the device. If the host sets the Maximum level and the
user password is forgotten, only a Security Erase Prepare/Security Unit command can unlock the device and all
data will be lost.

Password

The 32 bytes in the text of the password are always significant.

Master Password Revision Code

The Revision Code field is set with Master password. If Identifier is User, the Revision Code is not set. The Revi-
sion Code field is returned in Identify Device word 92. The valid Revision Codes are 0000h to FFFDh. The Default
Master Password Revision Code is FFFEh. The code FFFFh is reserved.

The setting of the Identifier and Security level bits interact as follows:

Identifier = User / Security level = High

The password supplied with the command will be saved as the new user password. The security mode feature
(lock function) will be enabled from the next power on. The drive may then be unlocked by either the user
password or the previously set master password.

Identifier = Master / Security level = High

This combination will set a master password but will NOT enable the security mode feature (lock function).

Identifier = User / Security level = Maximum

The password supplied with the command will be saved as the new user password. The security mode feature
(lock function) will be enabled from the next power on. The drive may then be unlocked by only the user pass-
word. The master password previously set is still stored in the drive but may NOT be used to unlock the
device.

Identifier = Master / Security level = Maximum

This combination will set a master password but will NOT enable the security mode feature (lock function).

«
...
163
164
165
166
167
...
»

Summary of Contents for HTS721010G9AT00


































































































































































































































Reviews:

No comments

Related manuals for HTS721010G9AT00

HD080HJ - 80 GB Hard Drive

Brand: Samsung Pages: 2

G2 PORTABLE HX-MU025DC

Brand: Samsung Pages: 36

Brand: QNAP Pages: 39

12big Rack Spare

Brand: LaCie Pages: 4

Brand: Dancover Pages: 36

Brand: Glyph Pages: 2

Brand: Transcend Pages: 25

Barracuda 180 Family

Brand: Seagate Pages: 2

Brand: ABSCO SHEDS Pages: 23

EonStor GS 3000 Series

Brand: Infortrend Pages: 134

Brand: Home Decorators Collection Pages: 4

Brand: HP Pages: 32

Brand: HP Pages: 44

Brand: HP Pages: 45

3PAR HP-UX 11i v2

Brand: HP Pages: 48

Brand: HP Pages: 70

Brand: HP Pages: 49

3PAR StoreServ 7200 2-node

Brand: HP Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands