manualshive.com logo in svg

Hitachi HTS721010G9AT00, Specifications

Share
Download
Hitachi HTS721010G9AT00 Specifications Download Page 187

Travelstar 7K100 Hard Disk Drive Specification

173

 

3

         

Off-line Read Scanning implemented bit

0

The device does not support Off-line Read Scanning

1

The device supports Off-line Read Scanning

4 

       

Self-test implemented bit

0

Self-test routing is not implemented

1

Self-test routine is implemented

5

 Reserved 

(0)

6

Selective self-test routine is not implemented

0

Selective self-test routine is not implemented

1

Selective self-test routine is implemented

7

Reserved (0)

13.39.2.8  S.M.A.R.T. Capability

This word of bit flags describes the S.M.A.R.T. capabilities of the device. The device will return 03h indicating that 
the device will save its Attribute Values prior to going into a power saving mode and supports the S.M.A.R.T. 
ENABLE/DISABLE ATTRIBUTE AUTOSAVE command.

Bit Definition

0

Pre-power mode attribute saving capability. If bit = 1, the device will save its Attribute Values prior to 
going into a power saving mode (Standby or Sleep mode).

1

Attribute auto save capability. If bit = 1, the device supports the S.M.A.R.T. ENABLE/ DISABLE 
ATTRIBUTE AUTOSAVE command.

2-15 

       Reserved (0)

13.39.2.9  Error logging capability

Bit

 Definition

7-1

     

Reserved (0)

  0 

     

The Error Logging support bit. If bit = 1, the device supports the Error Logging

13.39.2.10  Self-test failure check point

This byte indicates the section of self-test where the device detected a failure.

13.39.2.11  Self-test completion time

These bytes are the minimum time in minutes to complete the self-test.

13.39.2.12  Data Structure Checksum

The Data Structure Checksum is the 2's compliment of the result of a simple 8-bit addition of the first 511 bytes in 
the data structure.

Summary of Contents for HTS721010G9AT00


































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands