Hitachi HTS721010G9AT00 Specifications Download Page 91 | Manualshive

Page: 91 / 225

background image

Travelstar 7K100 Hard Disk Drive Specification

77

11.9.4.4 User Password lost

If the User Password is forgotten and High level security is set, the system user cannot access any data. However
the device can be unlocked using the Master Password.

If a system user forgets the User Password and Maximum security level is set, data access is impossible. However
the device can be unlocked using the Security Erase Unit command to unlock the device and erase all user data with
the Master Password.

Figure 4: Password lost

11.9.4.5 Attempt limit for the SECURITY UNLOCK command

The SECURITY UNLOCK command has an attempt limit, the purpose of which is to prevent someone from
attempting to unlock the drive with various passwords numerous times.

The device counts the password mismatch. If the password does not match, the device counts it without
distinguishing the Master password and the User password. If the count reaches 5, EXPIRE bit (bit 4) of Word 128
in Identify Device information is set, and the SECURITY ERASE UNIT command and the SECURITY UNLOCK
command are then aborted until there is a hard reset or a power off. The count and EXPIRE bit are cleared after a
power on reset or a hard reset.

User Password Lost

LEVEL ? High

Maximum

Erase Prepare Command
Erase Unit Command
with Master Password

Normal operation but data lost

Unlock EMD with Master Password

Normal operation

«
...
89
90
91
92
93
...
»

Summary of Contents for HTS721010G9AT00


































































































































































































































Reviews:

No comments

Related manuals for HTS721010G9AT00

Brand: EAST OAK Pages: 11

WDBAAE3200ASL - My Passport Studio

Brand: Western Digital Pages: 2

2,5" EXTERNAL HARD DRIVE KIT

Brand: Intenso Pages: 94

Brand: US Robotics Pages: 156

DiamondMax Plus9 120GB AT

Brand: Maxtor Pages: 79

Brand: B&B Electronics Pages: 2

STORAGE CAB4000 -

Brand: Tandberg Data Pages: 13

Brand: iStorage Pages: 23

Brand: Conner Pages: 81

Brand: Samsung Pages: 2

Brand: Samsung Pages: 4

Brand: Samsung Pages: 6

Brand: Samsung Pages: 43

Brand: Samsung Pages: 60

Brand: Black Box Pages: 20

Brand: Black Box Pages: 24

BUSH RANGER 3023BRK

Brand: ABSCO SHEDS Pages: 44

WD1200B008 - Series II USB

Brand: Western Digital Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands