12
English
NOTE
Standard Idle rpm is 2500–3000 rpm.
WARNING
When the engine is idling the cutting attachment must under no
circumstances rotate.
Air
fi
lter
(
Fig.
28
)
The air
fi
lter must be cleaned from dust and dirt in order to avoid:
○
Carburetor
malfunctions
○
Starting
problems
○
Engine power reduction
○
Unnecessary wear on the engine parts
○
Abnormal fuel consumption
Clean the air
fi
lter daily or more often if working in exceptionally
dusty areas.
Cleaning
the
air
fi
lter
Remove the air
fi
lter cover and the
fi
lter (24). Rinse it in warm soap
suds. Check that the
fi
lter is dry before reassembly. An air
fi
lter
that has been used for some time cannot be cleaned completely.
Therefore, it must regularly be replaced with a new one. A damaged
fi
lter must always be replaced.
Fuel
fi
lter
(
Fig.
29
)
Drain all fuel from fuel tank and pull fuel
fi
lter line from tank. Pull
fi
lter element out of holder assembly and rinse element in warm
water with detergent.
Rinse thoroughly until all traces of detergent are eliminated.
Squeeze, do not wring, away excess water and allow element to air
dry.
NOTE
If element is hard due to excessive dirt buildup, replace it.
Spark
plug
(
Fig.
30
)
The spark plug condition is in
fl
uenced by:
○
An incorrect carburetor setting
○
Wrong fuel mixture (too much oil in the gasoline)
○
A dirty air
fi
lter
○
Hard running conditions (such as cold weather)
These factors cause deposits on the spark plug electrodes, which
may result in malfunction and starting di
ffi
culties. If the engine
is low on power, di
ffi
cult to start or runs poorly at idling speed,
always check the spark plug
fi
rst. If the spark plug is dirty, clean it
and check the electrode gap. Re-adjust if necessary. The correct
gap is 0.6 mm. The spark plug should be replaced after about 100
operation hours or earlier if the electrodes are badly eroded.
Mu
ffl
er
(
Fig.
31
)
Remove the mu
ffl
er and clean out any excess carbon from the
exhaust port or mu
ffl
er inlet every 100 hours of operation.
Cylinder
(
Engine
cooling
) (
Fig.
32
)
The engine is air cooled, and air must circulate freely around engine
and over cooling
fi
ns on cylinder head to prevent overheating.
Every 100 operating hours, or once a year (more often if conditions
require), clean
fi
ns and external surfaces of engine of dust, dirt and
oil deposits which can contribute to improper cooling.
NOTE
Do not operate engine with engine shroud or mu
ffl
er guard
removed as this will cause overheating and engine damage.
Angle
transmission
(
Fig.
33
)
Check angle transmission or angle gear for grease level about every
50 hours of operation by removing the grease
fi
ller plug on the side
of angle transmission.
If no grease can be seen on the
fl
anks of the gears,
fi
ll the
transmission with quality lithium based multipurpose grease up to
3/4. Do not completely
fi
ll the transmission.
Blade
WARNING
Wear protective gloves when handling or performing
maintenance on the blade. (
Fig.
34
)
○
Use a sharp blade. A dull blade is more likely to snag and thrust.
Replace the fastening nut if it is damaged and hard to tighten.
○
When replacing blade, purchase one recommended by Hitachi,
with a 25.4 mm (one inch)
fi
tting hole.
○
When installing a saw blade, always face the stamped side up.
In the case of a 3 tooth blade, it can be used on either side.
○
Use the correct blade for the type of work.
○
When replacing blades, use appropriate tools.
○
When cutting edges become dull, re-sharpen or
fi
le as shown
in the illustration. Incorrect sharpening may cause excessive
vibration.
○
Discard blades that are bent, warped, cracked, broken or
damaged in any way.
NOTE
When sharpening blade it is important to maintain an original
shape of radius at the base of the tooth to avoid cracking.
Nylon
head
Nylon line replacement
○
Remove the cutting body cap by pushing inward the locking
tabs on the side of the nylon head (
Fig.
35
). Take out the spool
(
Fig.
36
), hook the new nylon line into the hole of the spool, then
wind it around the spool (
Fig.
37
).
When the nylon line has been wound around the spool,
temporarily fasten it in the opening of the spool at about 10 cm
from the end. (
Fig.
38
) Then thread the nylon line through the
hole on the side of the nylon head and place the cutting body
cap in reverse order of the cap removal. Pull the right and left
nylon lines until they are secured about 15
–
16 cm from the end.
(
Fig.
40
)
NOTE
○
The nylon head is designed for nylon lines with an outer
diameter of 2.5 mm. Do not use nylon lines with a di
ff
erent outer
diameter.
○
Make sure that the right and left nylon lines are of equal length
since vibrations will otherwise increase.
Maintenance
schedule
Below you will
fi
nd some general maintenance instructions. For
further information please contact your Hitachi dealer.
Daily
maintenance
○
Clean the exterior of the unit.
○
Check that the harness is undamaged.
○
Check the blade guard for damage or cracks. Change the guard
in case of impacts or cracks.
○
Check that the cutting attachment is properly centred, sharp,
and without cracks. An o
ff
-centre cutting attachment induces
heavy vibrations that may damage the unit.
○
Check that the cutting attachment nut is su
ffi
ciently tightened.
○
Make sure that the blade transport guard is undamaged and
that it can be securely
fi
tted.
○
Check that nuts and screws are su
ffi
ciently tightened.
Weekly
maintenance
○
Check the starter, especially the cord and return spring.
○
Clean the exterior of the spark plug.
○
Remove it and check the electrode gap. Adjust it to 0.6 mm, or
change the spark plug.
○
Clean the cooling
fi
ns on the cylinder and check that the air
intake at the starter is not clogged.
○
Check that the angle gear is
fi
lled with grease up to 3/4.
○
Clean the air
fi
lter.
Monthly
maintenance
○
Rinse the fuel tank with gasoline.
○
Clean the exterior of the carburetor and the space around it.
○
Clean the fan and the space around it.
000Book̲CG40EAS̲EE.indb 12
000Book̲CG40EAS̲EE.indb 12
2011/01/13 9:47:36
2011/01/13 9:47:36
