Hioki TS2400 Instruction Manual Download Page 108

Page: 108 / 116

104

Error display

Replacing batteries for PLC and servo pack

The PLC and the servo pack each have one replaceable built-in battery. This battery is used to

back up data to prevent the data stored in the PLC and the servo pack from being lost when the

power supply is turned OFF or is interrupted.

The built-in battery can retain the contents of the memory until the total time of power interruptions

reaches one year. The warranty period of the battery is five years from the date of purchase. These

values, however, differ according to the operating conditions, including the ambient temperature. If

the PC display shows

Low Battery of PLC (or Servopack)

, replace the battery with a new battery

(model: JZSP-BA01) within two weeks. Any delay in battery replacement will result in the loss of

data stored in the PLC and the servo pack.

The appearance of the battery is illustrated below.

LiTHIUM

Red lead

Black lead

JZSP-BA01 (Battery with Cable)

IMPORTANT

This battery is not commercially available. Contact Hioki for order.

Summary of Contents for TS2400





















































































































Search results

Summary of Contents for TS2400

Reviews:

Related manuals for TS2400

Brands by name

Popular brands

Hioki TS2400, Instruction Manual

Search results

Summary of Contents for TS2400

Reviews:

Related manuals for TS2400

Brands by name

Popular brands