background image

SAFETY REGULATIONS  |  

PAG. 4

2. SAFETY REGULATIONS

Before working on the machine carefully read the following safety regulations, 
and find out about the local requirements in safety.

The installation, operation, maintenance and repairs must be carried out only 
authorized and competent personnel.

The owner is responsible for the maintenance of the Lighting Tower in good safety 
conditions. The parts and accessories must be replaced if they are not in good 
functioning conditions.

2.1 GENERAL SAFETY PRECAUTIONS

 

Do not allow non-authorized people to be close to the Lighting Tower.

 

Do not allow people with pacemakers to get close to the tower as it 
may cause electromagnetic interferences on these devices.

 

Do not get close to the Tower wearing loose clothes or objects that 
may be attracted by the airflow or by the mobile parts of the engine.

 

lt is forbidden to dismount or disable any safety device.

 

lt is forbidden to lean on the Lighting Tower or leave objects on it.

 

Lower the mast when wind speed exceeds 80km/h.

 

Do not tow the lighting tower trailer on the highway at speeds 
exceeding 90km/h.

lf the Lighting Tower is driven by automatic driving sets, it is necessary to:

 

Place a red light that switches on when the unit is working, in a 
visible place.

 

Place a warning sign warning of the possibility that and automatic 
unexpected start up of the machine may occur.

 

Place an obligations sign stating: “All maintenance operations must 
be carried out with the genset in the LOCK position”.

 

For the emergency stop of the group, press “emergency stop” push 
button, located in the group or the emergency push button to be 
installed outside the engine room.

RAMIRENT

Summary of Contents for KT12000




















Reviews: