hilscher NANL-B500G-RE, User Manual

Page: 6 / 90

Introduction 6/90
1.1.2 List of revisions
Index Date Revisions
21 2018-03-14 Headings of safety information revised.
Section Data load limitation [ } page 61] added.
Section Analyzer device NANL-B500G-RE [ } page 83] CE information added.
22 2018-09-18 Section Overview installation update [ } page 28] revised.
Section Set the time for the autonomous operating mode [ } page 42] revised.
Section How to update the NANL-B500G-RE firmware using a web browser [ } page 63]
added.
Section Temperature control of the fan (NANL- B500G-RE) [
}
page 69] revised.
Section netANALYZER Configuration page [
}
page 36] added.
23 2019-01-21 Throughout the manual: 1.) Descriptions of the netANALYZER card NANL-C500-RE taken
from the manual. 2.) Information on personal injury taken from the manual, since the
netANALYZER portable device (device type NANL-B500G-RE) does not cause personal
injury.
Section Recording and analyzing data traffic [ } page 20]: "Delay of Ethernet signals by the
TAP" added.
Section System requirements [
}
page 23]: Supported/unsupported Windows
®
versions
listed.
Section Maximum permissible current consumption (external IO interface) [ } page 24]:
Correction of the value made in manual revision 22: For the analyzer device NANL-B500G-
RE the maximum permissible current consumption at the external I/O interface (for all I/O
signal pins 1, 3, 5 and 7 together) is:
1 mA (at 3.3V signal voltage at the external EA
interface)
Section Autonomous operating mode, general conditions and requirements [ } page 39]:
Note adds "Restarting the network for EtherNet/IP as prerequisite for process value
analysis in autonomous mode in snapshot mode".
Section Troubleshooting [ } page 73] Note added: User may need to check firewall
settings.
Added section SYS, STA0, STA1, I/O, LINK and RX (Front side) [
}
page 75]: Descriptions
on LED flashing sequences for missing network restart.
Section Analyzer device NANL-B500G-RE [ } page 83]: Isolation voltage for Ethernet
interface added.
24 2019-04-30 New function in the netANALYZER configuration page "Snapshot behaviour in autonomous
mode" added. Sections
Estimate required USB memory capacity for snapshot mode
theoretically [
}
page 44] and Set maximum number of snapshots for autonomous
operating mode [
}
page 46] added.
Terminology revised: "USB mass storage device" replaced by "USB memory device".
Revision of the structure in chapters 5 Getting started and Chapter 7 Commissioning.
Sections
Autonomous operating mode, general conditions and requirements [
}
page 39]
and chapter netANALYZER Configuration page [
}
page 36]moved and updated.
25 2019-07-04
Sections Requirements NANL-B500G-RE (Autonomous operating mode) [
}
page 25],
Notes for installation and operation [ } page 26], Autonomous operating mode, general
conditions and requirements [
}
page 39], Requirements for using the Autonomous
operating mode [ } page 40] and Troubleshooting [ } page 73] notes added about ext4 file
system support on USB memory device.
Section Estimate required USB memory capacity for snapshot mode
theoretically [ } page 44] descriptions about estimation of snapshot size added.
26 2019-07-10 Section Connection cable for external IO interface [ } page 81]
Adaption: Max. cable length 3 m.
Table 1: List of revisions
netANALYZER device NANL-B500G-RE | Installation, operation and hardware description
DOC091110UM26EN | Revision 26 | English | 2019-07 | Released | Public © Hilscher 2007-2019