hilscher NANL-B500G-RE User Manual Download

Page: 58 / 90

Commissioning

58/90

7.6.3

Application case 3

Like application case 2, but with further devices

This use case corresponds to the application case 2, but with the difference
that further devices are between the two analyzed Ethernet channels.

The analyzer device NANL-B500G-RE can analyze the following processes
and parameters:

the communication for two channels,

the forwarding time through several devices,

the cycle time and the jitter in the cyclically running protocols,

the changes of the data in the Ethernet frame through several devices,

the number of erroneous Ethernet frames.

To capture the communication of two channels, connect the analyzer
device NANL-B500G-RE via Ethernet cable (as shown in the figure).

Figure 15: Application case 3

Summary of Contents for NANL-B500G-RE



























































































Search results

Summary of Contents for NANL-B500G-RE

Reviews:

Related manuals for NANL-B500G-RE

Brands by name

Popular brands

hilscher NANL-B500G-RE, User Manual

Search results

Summary of Contents for NANL-B500G-RE

Reviews:

Related manuals for NANL-B500G-RE

Brands by name

Popular brands