HIKVISION DS-9100HFI-ST User Manual Download Page 15

Page: 15 / 200

User Manual of DS-9100HFI-ST Series DVR

1.1 Front Panel

The front panel of DS-9100HFI-ST is shown in Figure 1.1.

Figure 1.1 Front Panel

Table 1.1 Description of Control Panel Buttons

No.

Name

Function Description

ALARM

Alarm indicator turns red when a sensor alarm is detected.

READY

Ready indicator is normally green, indicating that the DVR is functioning

properly.

STATUS

Status indicator turns green when DVR is controlled by an IR remote.

Indicator turns red when controlled by a keyboard and purple when IR

remote and keyboard is used at the same time.

HDD

HDD indicator blinks red when data is being read from or written to HDD.

MODEM

Reserved for future usage.

TX/RX

TX/RX indictor blinks green when network connection is functioning

properly.

GUARD

Guard indicator turns green when the device is in armed status; at this

time, an alarm is enabled when an event is detected. The indicator turns

off when the device is unarmed. The arm/disarm status can be changed by

pressing and holding on the ESC button for more than 3 seconds in live

view mode.

IR Receiver

Receiver for IR remote

Front Panel Lock

You can lock or unlock the panel by the key.

DVD-ROM

Slot for DVD-ROM. (Optional)

Alphanumeric Buttons

•

Switching to the corresponding channel in Live view or PTZ Control

mode.

•

Inputting numbers and characters in Edit mode.

•

Switching between different channels in Playback mode.

•

The light of the button is green when the corresponding channel is

recording; it is red when the channel is in network transmission status; it is

pink when the channel is recording and transmitting.

USB Interfaces

Universal Serial Bus (USB) ports for additional devices such as USB

mouse and USB Hard Disk Drive (HDD).

ESC

Back to the previous menu

Pressing for arming/disarming the DVR in Live View mode.

Summary of Contents for DS-9100HFI-ST









































































































































































































Search results

Summary of Contents for DS-9100HFI-ST

Reviews:

Related manuals for DS-9100HFI-ST

Brands by name

Popular brands

HIKVISION DS-9100HFI-ST, User Manual

Search results

Summary of Contents for DS-9100HFI-ST

Reviews:

Related manuals for DS-9100HFI-ST

Brands by name

Popular brands