manualshive.com logo in svg

HighEasy HY-8004HC, User Manual, Page: 50 / 94

Share
Download
HighEasy HY-8004HC User Manual Download Page 50

                                                                                                                         

Page 50 of total 94 pages 

Timing module mainly starts different type recording in a setted period of time by setting record type, 

period of time and the corresponding channel number.It contains two periods of time. By operating the 

state of the checkbox 

  ,you can set the time period.

 

means to enable the time period. Notice that 

the start time of each period should be less than the end time, and the start time of the second period 

should be more than the end time of the first period when enable the two periods. 

The setting time of every record type should not overlap with the others.   

If timing recording is required, firstly should cancel all the other types recording including manual 

recording, alarm linkage recording and motion detection recording, and then start timing recording. 

If there is Alarm in with linkage to corresponding channel, then recording begins at corresponding 

channel within the linkage recording time of Alarm in which is set by corresponding channel. If there is 

manual recording previously, close firstly manual recording, if there is motion detection recording 

previously, then it will not reopen the file, and write directly the data in video file of motion detection. 

If there is motion detection alarm with linkage to corresponding channel, then recording begins at 

corresponding channel within the motion detection recording time which is set by corresponding 

channel. If there is manual recording previously, turn off the manual, if there is motion detection 

recording previously, then not reopen file, and write directly in Alarm in linkage video file.   

If manual record is required, it should be performed out of time periods of timing recording, Alarm in 

linkage recording, motion detection linkage recording and etc; otherwise, manual recording will wait till 

it is out of the foresaid periods, if manual recording has started and entered one of the above mentioned 

time periods, manual recording will stop; until the period ends, manual recording must be canceled 

manually.

  

 NOTE

 

All

 in week indicates everyday, All items refer to all settings of this channel applied in all 

channels. 

5.3.4.4.4  Network setting 

Network setting is to set DVR network parameters including IP address, subnet mask, default gateway, 

management server, PPPoE, dynamic domain name and NAT and etc. 

 

Select Network, press ok key , it will enter the following figure:

 

Summary of Contents for HY-8004HC































































































Reviews:

No comments