High-Flying HF-LPT220 User Manual Download Page 54

Page: 54 / 65

HF-LPT220 Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

- 54 -

4.2.2.69.

AT+WPSBTNEN



Function: Enable/Disable WPS function.



Format:



Query Operation

AT+WPSBTNEN<CR>

+ok=<status> <CR><LF><CR><LF>



Set Operation

AT+ WPSBTNEN =<status><CR>

+ok<CR><LF><CR><LF>



Parameters:



status:



on: Enable WPS function



off: Disable WPS function.

Note: The router WPS function must be open first then enable module WPS Scan function.

The module will quit WPS scan status if there is no WPS router in 5 seconds.

4.2.2.70.

AT+LPTIO



Function: nReady,nLink, WPS function mapping. Setting is valid after reset.



Format:



Query Operation

AT+LPTIO<CR>

+ok=<status> <CR><LF><CR><LF>



Set Operation

AT+LPTIO =<status><CR>

+ok<CR><LF><CR><LF>



Parameters:



status: nReady,nLink, WPS function mapping.



off/lpb100: nReady,nLink, WPS function are mapping to HF-LPB120

corresponding pin.(Pin44, Pin43, Pin15)



on/lpt100: nReady,nLink, WPS function are mapping to HF-LPT100

corresponding pin.(Pin9, Pin10, Pin8)



lpt200: nReady,nLink, WPS function are mapping to HF-LPT200

corresponding pin.(Pin11, Pin13, Pin14)

4.2.2.71.

AT+WIFI



Function: Enable/Disable Wi-Fi Command, need to update to V1.0.05 firmware to use

this command..



Format:



Query Operation

AT+WIFI<CR>

+ok=<status> <CR><LF><CR><LF>



Set Operation

AT+WIFI =<status><CR>

+ok<CR><LF><CR><LF>

Summary of Contents for HF-LPT220


































































Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands

High-Flying HF-LPT220, User Manual

Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands