High-Flying HF-LPT220 User Manual Download Page 50

Page: 50 / 65

HF-LPT220 Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

- 50 -

Note:

After execute this command, the HF-LPB120 will automatic start upgrade base on the

setting of UPURL, UPFILE command contents;

4.2.2.56.

AT+DISPS



Function: Set/Query power save parameters;



Format:



Query Operation

AT+DISPS<CR>

+ok=<ret><CR><LF><CR><LF>



Set Operation

AT+DISPS=<mode><CR><LF><CR><LF>



Parameters:



ret:



No: Enable power save (default)



Yes: Disable power save



mode:



No: Enable power save



Yes: Disable power save

4.2.2.57.

AT+NTPRF



Function: Set /Query time calibration interval



Format:



Query Operation

AT+NTPRF<CR>

+ok=<num><CR><LF><CR><LF>



Set Operation

AT+NTPRF=<num><CR>

+ok<CR><LF><CR><LF>



Parameters:



num

：

time calibration inverval

，

range:0~720, default:30 minutes, 10 minutes for

each step, set 0 means no time calibration automatically.

4.2.2.58.

AT+NTPEN



Function: Enable/Disable time calibration function. Setting is valid after reset.



Format:



Query Operation

AT+NTPEN<CR>

+ok=<status><CR><LF><CR><LF>



Set Operation

AT+NTPEN=<status><CR>

+ok<CR><LF><CR><LF>



Parameters:



status

：

status of time calibration



：

Enable time calibration

Summary of Contents for HF-LPT220


































































Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands

High-Flying HF-LPT220, User Manual

Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands