High-Flying HF-LPT220 User Manual Download Page 33

Page: 33 / 65

HF-LPT220 Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

- 33 -

Instruction

Description

WALKIND

Enable/Disable indication of connection status.

WAPMXSTA

Set/Query max STA devices supported for AP.

Remote Upgrade Instruction Set

OTA

Upgrade Firmware

UPURL

Set/Query remote upgrade URL address

UPFILE

Set/Query remote upgrade configure file name

LOGSW

Open/Close remote upgrade log

LOGPORT

Set/Query UDP port of remote upgrade log

UPST

Start remote Application upgrade

Power Management Instruction Set

DISPS

Set/Query power save parameters

Network Time Set

NTPRF

Set/Query time calibration interval

NTPEN

Enable/Disable time calibration function

NTPTM

Query time

NTPSER

Set/Query NTP server IP

Others Instruction Set

WRMID

Set module ID

RLDEN

Set/Query GPIO45 status

ASWD

Set/Query WiFi configuration code

MDCH

Set Wi-Fi Auto Switch Function

TXPWR

Set/Query Wi-Fi Transmit Power

SMTLK

Start SmartLink function

SMTLKVER

Set/Query SmartLink version

WPS

Start WPS function

WPSTNEN

Enable/Disable GPIO 15 WPS function

LPTIO

nRead/nLink/WPS function mapping

WIFI

Enable/Disable Wi-Fi

SMEM

Query RAM status

NDBGL

Set UART debug information

Note: Some AT is not supported yet

（

The above AT command with line through

）

. It will

be updated for later firmware.

4.2.2.1.

AT+E



Function: Open/Close show back function;



Format:



Set Operation

AT+E=<status><CR>

+ok<CR><LF><CR><LF>



Parameters:



status: Echo status



on: Open echo



off: Close echo

When HF-LPB120 module firstly switch from transparent transmission to configuration mode, show
back status is open, input “AT+E” to close show back function, input“AT+E” again to open show back

function.

Summary of Contents for HF-LPT220


































































Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands

High-Flying HF-LPT220, User Manual

Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands