High-Flying HF-LPT220 User Manual Download Page 39

Page: 39 / 65

HF-LPT220 Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

- 39 -



Parameters:



sta: feedback result



Success



Timeout



Unknown host

4.2.2.22.

AT+NETP



Function: Set/Query network protocol parameters, Setting is valid after reset.



Format:



Query Operation

AT+NETP<CR>

+ok=<protocol,CS,port,IP><CR><LF><CR><LF>



Set Operation

AT+NETP=<protocol,CS,port,IP><CR>

+ok<CR><LF><CR><LF>



Parameters:



protocol:



TCP



UDP



CS: Network mode:



SERVER



CLIENT



Port: protocol port ID: Decimal digit and less than 65535



IP: Server’s IP address when module set as client

If set as UDP SERVER, the module will save the IP address and port of the latest UDP
packet received. The data will be sent to the saved IP address and port. If the module hasn’t

saved any IP address and port when power up. The data will be sent to the IP address and port

which is set by this command.

If set as UDP,CLIENT, the data will always be sent to the IP address and port set by this

command.

4.2.2.23.

AT+MAXSK



Function:Set/ Query TCP Client connection number.



Format:



Query Operation

AT+MAXSK<CR>

+ok=<num><CR><LF><CR><LF>



Set Operation

AT+MAXSK=<num><CR>

+ok<CR><LF><CR><LF>



Parameters:



num: TCP Client connection number. Range: 1~5. 5 is the default value it means

when the module work in TCP server , it accepts max 5 TCP client connect to it.

Summary of Contents for HF-LPT220


































































Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands

High-Flying HF-LPT220, User Manual

Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands