High-Flying HF-LPT220 User Manual Download Page 41

Page: 41 / 65

HF-LPT220 Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

- 41 -

When setting, “off” means close TCP link. After finish this command, module disconnect TCP

link and not connect again. “On” means open TCP link. After finish this command, module re-

connect TCP server right away.

4.2.2.27.

AT+SOCKB



Function: Set/Query SOCKB parameters. Setting is valid after reset.



Format:



Query Operation

AT+SOCKB<CR>

+ok=<protocol,port,IP><CR><LF><CR><LF>



Set Operation

AT+SOCKB=<protocol,port,IP><CR>

+ok<CR><LF><CR><LF>



Parameters:



Protocol: Protocol type:



TCP: Only for TCP Client



UDP: UDP Client



UDPS: UDP Server



Port: Protocol Port in decimal, less than 65535



IP: Destination IP address, domain name is support

If set as UDP SERVER, the module will save the IP address and port of the latest UDP

packet received. The data will be sent to the saved IP address and port. If the module

hasn’t

saved any IP address and port when power up. The data will be sent to the IP address and

port which is set by this command.

If set as UDP,CLIENT, the data will always be sent to the IP address and port set by this

command.

4.2.2.28.

AT+TCPDISB



Function: Open/Close SOCKB connection



Format:



Query Operation

AT+TCPDISB<CR>

+ok=<sta><CR><LF><CR><LF>



Set Operation

AT+TCPDISB =<on/off><CR>

+ok<CR><LF><CR><LF>



Parameters:

When setting, “off” means close TCP link. After finish this command, module disconnect TCP

link and not connect again. “On” means open TCP link. After finish this command, module re-

connect TCP server right away.

4.2.2.29.

AT+TCPTOB



Function: Set/Query Operation SOCKB TCP timeout. Setting is valid after reset.



Format:

Summary of Contents for HF-LPT220


































































Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands

High-Flying HF-LPT220, User Manual

Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands