High-Flying HF-LPT220 User Manual Download Page 42

Page: 42 / 65

HF-LPT220 Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

- 42 -



Query Operation

AT+TCPTOB<CR>

+ok=<time><CR><LF><CR><LF>



Set Operation

AT+TCPTOB=<time ><CR>

+ok<CR><LF><CR><LF>



Parameters



Time: TCP timeout



<= 600:600s



>=0:0 means no timeout



Default:300s

If the SOCKB TCP don't receive any data from TCP server for TCP tmeout setting, the

module will break and reconnect the TCP server. If it receive data from server, the timeout

counter will be clear.

4.2.2.30.

AT+TCPLKB



Function:Query SOCKB connection status



Format:

AT+TCPLKB<CR>

+ok=<sta><CR><LF><CR><LF>



Parameters:



sta.: SOCKB connection status



on: TCP connected



off: TCP disconnected

4.2.2.31.

AT+SNDB



Function: Send datas to SOCKB at Command Mode



Format:

AT+SNDB=<data_lenth ><CR>

+ok<CR><LF><CR><LF>



Parameters:



data_lenth: Lenth of send data. Range: 0~1000 Byte

The UART port will wait 3 seconds for input after this command is sent OK. The data received

from UART port is sent to SOCKB. If the interval of two bytes is more than 10ms, the data will be

sent instantly.

4.2.2.32.

AT+RCVB



Function: Receive datas from SOCKB at Command Mode



Format:

AT+RCVB=<data_lenth><CR>

+ok=< data_lenth, data_content><CR><LF><CR><LF>



Parameters:



data_lenth: Lenth of receive data. Range: 0~1000 Byte



data_content: contents of receive data.

Summary of Contents for HF-LPT220


































































Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands

High-Flying HF-LPT220, User Manual

Search results

Summary of Contents for HF-LPT220

Reviews:

Related manuals for HF-LPT220

Brands by name

Popular brands