Hekatron SVG 522 Instruction Manual Download Page 31

31/68

7002985 300709.KET   Release 06.06.2017 

Hekatron Vertriebs GmbH · Brühlmatten 9 · D-79295 Sulzburg

6 Electrical installation

6.5.1  PCB TKS 03 voltage supply

Name

Data stream

Function

Data

Activation

Terminal 1

Input

TKS 03 voltage supply 

24 V DC SVK 47 +UA

Terminal 2

Input

TKS 03 voltage supply

GND

SVK 47 –UA

In the SVG 522 version with TSK 03, these connections have already been pre-
wired at the factory.

Fig. 18: 

Connections pre-wired at the factory

6.5.2  Incorporation of SVK 47 fault messages

Battery failure, processor failure and low battery voltage of the power supply 
board SVK 47 are signalled to the door control board TSK 03 and evaluated as an 
alarm from the fire detectors.

Name

Data stream

Function

Data

Activation

Terminal 3

Output

Voltage supply

24 V DC Unassigned

Terminal 4

Output

Voltage supply

GND

Unassigned

Terminal 5

Unassigned

Connection point terminal

Unas-
signed

Unassigned

Terminal 6

Output

Monitoring of SVK 47 faults

SVK 47 1.9

Terminal 7

Input

Monitoring of SVK 47 faults

SVK 47 1.4

In the SVG 522 version with TSK 03, these connections have already been pre-
wired at the factory.

Unassigned

SVK 47 fault

SVK 47 fault

Fig. 19: 

Connections pre-wired at the factory

Summary of Contents for SVG 522





































































Reviews: