background image

Heat & Glo  •  6000PLUS  •  2063-900  Rev. E  •  11/05

11

Step 4.  Positioning, Leveling, and

               Securing the Fireplace

To properly position, level, and secure the fireplace:
• Place the fireplace into position (see Figure 4).
• Level the fireplace from side to side and from front to

back.

• Shim the fireplace with non-combustible material, such

as sheet metal, as necessary.

• Secure the fireplace to the framing by nailing or screwing.

!

!

Figure 4.  Proper Positioning, Leveling,

    and Securing of a Fireplace

Step 5. The Gas Control System

WARNING:  THIS UNIT IS NOT FOR USE WITH

SOLID FUEL.

The gas control system used with this model is the Intellifire.

Intellifire System

The Intellifire system includes a 3V control valve, electronic

module, and intermittent pilot.

WARNING:  CONTINUOUS 110-120 VAC SER-

VICE MUST BE WIRED TO THE FIREPLACE

JUNCTION BOX.

WARNING:

To ensure proper clearances

the front framing header

must be installed on its

narrow edge and to the

front of the frame.

!

Step 3.  Installing the Vent System

A

.   42”

         B

.  38 1/2”

  C

.  22”

Figure 3. Framing Dimensions

Framing should be constructed of 2 X 4 lumber or heavier.

WARNING:

To ensure proper clearances

the front framing header

must be installed on its

narrow edge and to the front

of the frame.

Step 2.  Framing the Fireplace

Fireplace framing can be built before or after the fireplace is

set in place. Framing should be positioned to accommo-

date wall coverings and fireplace facing material. The dia-

gram below shows framing reference dimensions.

CAUTION:

 MEASURE FIREPLACE DIMENSIONS AND

VERIFY FRAMING METHODS AND WALL COVERING

DETAILS BEFORE FRAMING.

WARNING: REFER TO THE HRV200PLUS

INSTALLATION  MANUAL  FOR  PROPER

VENTING  CONFIGURATIONS  FOR  THE

6000PLUS GAS APPLIANCE.

Summary of Contents for 6000PLUS




















Reviews: