background image

L2 S

ERIES

DV ZC Gas Fireplace

1700JN (NG) & 1700JP (LPG)

Installation & Owner’s Manual

4005427-02

©2016, Miles Industries Ltd.

This manual contains instructions to install the

 

ENGINE ONLY. 

A front or trim kit is

 REQUIRED 

to install the engine. A barrier screen is provided 
with the front or trim kit. 

Refer to the manual 

supplied with the front or trim for installation.

— Do not store or use gasoline or other 

fl

 ammable vapors and liquids in the 

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

 

Do not try to light any appliance.

 

Do not touch any electrical switch; do 
not use any phone in your building.

 

Leave the building immediately.

 

Immediately call your gas supplier from 
a neighbor’s phone. Follow the gas 
supplier’s instructions.

 

If you cannot reach your gas supplier, 
call the 

fi

 re department.

— Installation and service must be 

performed by a quali

fi

 ed installer, service 

agency or the gas supplier.

Ce guide est disponible en français sur demande.

This appliance is only for use with the type 
of gas indicated on the rating plate. This 
appliance is not convertible for use with 
other gases, unless a certi

fi

 ed kit is used.

This appliance is a domestic room-heating 
appliance. It must not be used for any other 
purposes such as drying clothes, etc.
This appliance is suitable for installation in a 
bedroom or bed sitting room.

This appliance may be installed in an 
after-market permanently located, 
manufactured (mobile) home where not 
prohibited by local codes.

HOT GLASS

 WILL 

CAUSE BURNS.

DO NOT TOUCH 

GLASS 

UNTIL COOLED.

NEVER 

ALLOW CHILDREN 

TO TOUCH GLASS.

DANGER

!

A barrier designed to reduce the risk of burns from the hot 
viewing glass is provided with this appliance and shall be 
installed for the protection of children and other at-risk 
individuals.

  

!

  WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly 
could result in serious injury, death, or 
property damage.

INSTALLER

Leave this manual 

with the appliance.

CONSUMER

Retain this manual 

for future reference.

Please read this manual 
BEFORE installing and 
operating this appliance.

Summary of Contents for 1700JN

































































Reviews: