background image

Heat & Glo  •  6000PLUS  •  2063-900  Rev. E  •  11/05

8

2

Getting Started

The vent system components and trim doors are shipped

in separate packages. Gas logs are shipped in the unit.

Log installation instructions are provided in the manual bag

assembly shipped with the unit.

Read  all  of  the  instructions  before  starting  the

installation. Follow these instructions carefully during

the installation to ensure maximum safety and benefit.

Failure  to  follow  these  instructions  will  void  the

owner’s warranty and may present a fire hazard.

The Heat & Glo Warranty will be voided by, and Heat & Glo

disclaims any responsibility for, the following actions:
• Installation of any damaged fireplace or vent system

component.

• Modification of the fireplace or vent system.
• Installation other than as instructed by Heat & Glo.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not manu-

factured and approved by Heat & Glo, not withstanding

any independent testing laboratory or other party approval

of such component part or accessory.

ANY  SUCH ACTION  MAY  POSSIBLY  CAUSE A  FIRE

HAZARD.

When planning a fireplace installation, it’s necessary to

determine:

Where the unit is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring.

Framing and finishing details.

Whether optional accessories—devices such as a fan,

wall switch, or remote control—are desired.

If the fireplace is to be installed on carpeting or tile, or on

any  combustible  material  other  than  wood  flooring,  the

fireplace should be installed on a metal or wood panel that

extends the full width and depth of the fireplace.

WARNING: THE 6000PLUS IS DESIGNED TO BE

USED  WITH  THE  HRV200PLUS  ONLY!  THE

6000PLUS WILL NOT VENT CORRECTLY UNLESS

IT IS CONNECTED TO THE HRV200PLUS. REFER

TO THE HRV200PLUS INSTALLATION MANUAL FOR

ADDITIONAL  INSTALLATION AND  VENTING  IN-

STRUCTIONS.

!

The information contained in this 

Installers Guide

, unless

noted  otherwise,  applies  to  all  models  and  gas  control

systems. Gas fireplace diagrams, including the dimensions,

are shown in this section.

Pre-install Preparation

This gas fireplace and its components are tested and safe

when installed in accordance with this 

Installers Guide

.

Report  to  your  dealer  any  parts  damaged  in  shipment,

particularly the condition of the glass. 

Do not install any

unit with damaged, incomplete, or substitute parts.

Introducing the Heat & Glo Gas Fireplaces

Summary of Contents for 6000PLUS




















Reviews: