background image

Heat & Glo  •  6000PLUS  •  2063-900  Rev. E  •  11/05

15

Step 9.  Sequence of Operation

The 6000PLUS must be installed with an HRV200PLUS.

The  appliance  and  ventilator  operate  as  a  system.  The

HRV200PLUS controls many of the operational sequences

for the system, and the 6000PLUS gas appliance maintains

safety control for the combustion process. The sequence of

operation for the system is as follows:

1. Appliance  Mode

a. The user creates a demand for system operation

using remote control, wall switch or thermostat.

b. A 12V DC signal is sent from the HI terminal on

the appliance circuit board to the HRV200PLUS.

c. The HRV200PLUS does the following:

1. Turns blowers on to high speed.

2. Positions HRV200PLUS dampers (if installed) for

appliance operation.

3. Presents a 15-second delay (pre-purge) before burn-

ers are lit.

4. Sends a 12 DV signal to the gas appliance burner

(by energizing relay K2 on the circuit board) and

closing the contacts between the R1 and R2 termi-

nals to initiate the ignition sequence.

d. The 6000PLUS does the following:

1. The  6000PLUS  awaits  the  signal  from  the

HRV200PLUS to light the burners.

2. When the contact between R1 and R2 closes in

the HRV200PLUS, the intermittent pilot ignition (IPI)

system activates and lights the burners.

3. When the user demand for appliance operation is

removed. The HRV200PLUS de-energizes C2 and

R1 terminals, terminating burner operation.

4. There is a 20-second delay (post-purge) on the HRV

high fan and a 5-minute delay on the HRV low fan.

e. The HRV200PLUS shuts off.

2. HRV200PLUS Defrost  Mode

!

a. The HRV200PLUS demands gas appliance opera-

tion for defrost. This occurs when the following

conditions exist:

1. The appliance is not in use.

2. The outdoor temperature falls below 25

o

 F.

3. The  DEFC1  jumper  is  not  installed  on  the

HRV200PLUS circuit board.

b. The HRV200PLUS does the following:

1. Turns blowers on to high speed.

2. Positions HRV200PLUS dampers (if installed) for

appliance operations.

3. Presents a 15-second delay (pre-purge) before burn-

ers are lit.

4. Closes the contacts between the R1 and R2 termi-

nals to initiate the ignition sequence (by energiz-

ing relay K1 on the circuit board).

c. The 6000PLUS does the following:

1. The  6000PLUS  awaits  the  signal  from  the

HRV200PLUS to light the burners.

2. When the contact between R1 and R2 closes in

the HRV200PLUS, the intermittent pilot ignition (IPI)

system activates and lights the burners.

3. When the user demand for appliance operation is

removed. The HRV200PLUS de-energizes C2 and

R1 terminals, terminating burner operation.

4. There is a 20-second delay (post-purge) on the HRV

high fan and a 5-minute delay on the HRV low fan.

d. The HRV200PLUS shuts off.

WARNING: THE APPLIANCE MAY OPERATE TO

DEFROST THE HRV200PLUS AT ANY TIME.

NOTE: The HRV200PLUS can use indoor air instead of the

gas appliance for defrost if the optional defrost kit (part#

HRV99DEFKIT) is installed.

Summary of Contents for 6000PLUS




















Reviews: