Hearth & Home Quadra-Fire CB1200 Installation Manual Download Page 4

4

07/22

7027-804H 

C. Glass Specifications

This appliance is equipped with 5mm ceramic glass. 

Replace glass only with 5mm ceramic glass. Please contact 

your dealer for replacement glass.

D. Electrical Rating

115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps

E. Mobile Home Approved

•  This appliance is approved for mobile home 

installations when not installed in a sleeping room and 

when an outside combustion air inlet is provided.

• 

The structural integrity of the mobile home floor, ceiling, 

and walls must be maintained.

•  The appliance must be properly grounded to the frame 

of the mobile home and use only Listed pellet vent 

Class “L” or “PL” connector pipe.

• 

Outside Air Kit, part OAK-ACC must be installed in a 

mobile home installation.

H. Sleeping Room

When installed in a sleeping room it is recommended 

that 3ft of vertical be installed prior to horizontally exiting 

the room and a smoke/CO alarm be installed in the 

bedroom.  The size of the room must be at least 

50ft³ per 1,000 Btu/hr stove input, if the stove exceeds the 

room size, out air must be installed.

I. California - Prop65

This product and the fuels used to operate this product (wood), and the 

products of combustion of such fuels, can expose you to chemicals 

including carbon black, which is known to the State of California to 

cause cancer, and carbon monoxide, which is known to the State of 

California to cause birth defects or other reproductive harm. For more 

information go to: WWW.P65Warnings.ca.gov

WARNING

F. Non-Combustible Materials

Material which will not ignite and burn, composed of any 

combination of the following:

 - Steel

 - Plaster

 - Brick

 - Iron

 - Concrete

 - Tile

 - Glass

 - Slate

Materials reported as passing ASTM E 136, Standard 

Test Method for Behavior of Metals, in a Vertical Tube 

Furnace of 750°C. 

G. Combustible Materials

Material made of/or surfaced with any of the 

following materials:

 - Wood

 - Compressed Paper

 - Plant Fibers

 - Plastic

 -

Plywood/OSB

 - Sheet Rock (drywall)

Any material that can ignite and burn:

 flame proofed or not, 

plastered or non-plastered.

Improper installation, adjustment, alteration, service or 

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualified 

installer, service agency or your dealer.

NOTE:

 Hearth & Home Technologies, manufacturer 

of this appliance, reserves the right to alter 

its products, their specifications and/or price 

without notice.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any 

responsibility for, and the warranty will be 

voided by, the following actions:

•  Installation and use of any damaged appliance. 

• 

Modification of the appliance.

•  Installation other than as instructed by Hearth & 

Home Technologies.

•  Installation and/or use of any component part not 

approved by Hearth & Home Technologies.

• 

Operating appliance without fully assembling 

all components.

• 

Operating appliance without legs attached (if 

supplied with appliance).

• 

Do NOT Over fire

 - If appliance or chimney connector 

glows, you are over firing.

Any such action that may cause a fire hazard. 

Summary of Contents for Quadra-Fire CB1200

































Reviews: