18
Chemistry Config.
to enter
Press to access Chemistry Config. Wizard
Move to previous/next menu item
Chemistry Configuration Wizard
Requires use of the optional AQL-CHEM Sensing Kit.
Following the steps of the Chemistry Config.
Wizard will set up the AQL-CHEM to sense ORP and pH levels and, if the chlorination function is
used, can configure the Aqua Plus 16v to generate the correct amount of chlorine to properly sanitize
the pool. Refer to the AQL-CHEM manual for more detailed information.
Pool/Spa Config.
+ to view/change
Pool/Spa Setup
Pool and Spa-Std
Spa Spillover
Enabled
Heaters
Htr1=Spa,Htr2=Pool
Filter Operation
Spa Spillover
Push to access Pool/Spa options
Rotates between Pool and Spa-Std
, Pool and Spa-Dual,
Pool Only, and Spa Only options
(default)
Toggle between Enabled and Disabled
Spa Spillover
(default)
Toggle between Htr1=Spa, Htr2=Pool (default) and Shared Heaters
Toggle between Pool Only
and Spa Spillover options
(default)
Move to previous/next configuration menu
Move to next menu item
Move to next menu item or previous/next configuration menu
Move to next menu item
Move to previous/next configuration menu
if “Pool and Spa-Std or Dual” is
selected and if “Spa Spillover” is enabled
Spa - CountDn
00:30
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15..., (default is 4:00))
Move to next menu item
if “Pool and Spa-Std” is selected
if “Pool and Spa-Dual” is selected
if “Pool and Spa-Std or Dual” is selected
V1=Aux1, V2=Aux2
Disabled
Toggle between Enabled and Disabled (default)
if “Pool Only” or “Spa Only” is selected
Move to previous/next configuration menu
Filter Off Valve
Change: Enabled
Toggle between Enabled
and Disabled
(default)
if “Pool and Spa-Std” is selected
Move to previous/next configuration menu
Pool/Spa Setup
If “Pool Only” or “Spa Only” are selected, then the pool/spa valves are not needed and pushing the
POOL/SPA button on the display/keypad will have no effect. If “Pool and Spa-Std” is selected, then
the pool/spa suction and return valve actuators should be connected to the Aqua Plus 16v. Pressing
the POOL/SPA button on the display/keypad will allow the homeowner to alternate between pool and
spa operation. If “Pool and Spa-Dual” is selected, then only the Pool/Spa return valve actuator
should be connected to the Aqua Plus 16v.
Heaters
This menu will only appear if Pool/Spa setup is set to “Pool and Spa-Dual”. This allows the heater(s)
to either be shared between the pool and spa (“Shared” selected) or for Heater1 to be dedicated to the
spa and Heater2 to be dedicated to the pool (“Htr1=Spa, Htr2=Pool” selected).
Spa CountDn
This menu will appear only if Pool/Spa Setup is set to “Pool and Spa-Std”. This setting is the time,
after you manually switch the Pool/Spa valves to “Spa Only”, until the Aqua Plus 16v automatically
returns the valves to their previous positions. It is programmed in increments of 5 minutes, from
“Manual On/Off” (0 minutes) to
“21:00” (21 hours).
The filter is forced on during this time period.
Spa Spillover
When spa spillover is “Enabled” and “Pool and Spa-Std”, the homeowner will be able to rotate
through “Pool Only” (both suction and return valves switched to pool), “Spa Only” (both suction and
return valves switched to spa) and “Spillover” (suction valve switched to pool and return valve
switched to spa) by successive presses of the “Pool/Spa” button. For “Pool and Spa-Dual”, only
“Pool Only” and “Spillover” are available.
29
NOTE: The configuration for Valve3 and Valve4 are identical. However, if Heater2 was enabled, then the Valve4 configuration
will not appear (a single relay is used to implement either the Heater2 function or the Valve4 function--it can not do both). For
PS-16, see aux logic on page 27 for control of Valves7, 8, 9 and 10.
Valve3
Disabled
Freeze
Toggle between Enabled and Disabled (default) Valve3 Freeze
Move to previous/next configuration menu
for all functions except group and super chlorinate
Valve3 Config.
+ to view/change
Valve3 Function
Solar
Valve3 Name
Waterfall
Push to access Valve3 options
Rotates between
Manual On/Off (default), Countdown Timer,
Timeclock, Solar, In-floor Cleaner, Group, and Super Chlorinate
Move to previous/next configuration menu
Move to next menu item
Valve3
Disabled
Interlock
Toggle between Enabled and Disabled (default) Valve3 Interlock
Move to next menu item
for all functions except solar, group or super chlorinate
for all functions except solar, group or super chlorinate
Rotates between all available names
Move to next menu item
Valve3 Group
Filter: Unaffected
Valve3 Group
Timer: None(Manual)
Options available depend on the function that is selected
Rotates between Manual On/Off (default),Countdown Timer and Timeclock
Move to previous/next menu item or next configuration menu
Move to next menu item
for group function only
for group function only
Valve3 Ext Input
Disabled
Toggle between Enabled and Disabled (default)
Move to previous/next configuration menu
if filter pump is set to variable speed
and the relay type is set to standard
Valve3 Pump Spd
Settings Menu
Select Settings Menu (default) or desired pump speed (Filter Lowest to Highest)
Move to previous/next configuration menu
Valve3 Name
The Aqua Plus 16v allows you to assign any one of a number of names (e.g. “Cleaner Valve, Waterfall
valve, Solar Valve, etc.) to each of the valve output control function. This will make the Aqua Plus 16v
much more user friendly to the homeowner when they want to turn various valves on or off or program
the timeclocks. A sheet of small name labels is included with the Aqua Plus 16v main unit and each
remote display/keypad so that the “Valve3” (and “Valve4”) pushbutton can be labeled the same as the
name that you have assigned.
Valve3 Function
Manual On/Off (default)
– the valve3 relay will alternate between turning on and off when the
VALVE3 button is pressed. There is no automatic control logic. The VALVE3 button can also be used
to turn the valve output on or off.
Countdown Timer
– the valve3 relay will turn on when the VALVE3 button is pressed and then will
turn off automatically after a programmed time (see Timers Menu in the Operations Manual). The
VALVE3 button can also be used to turn the output off.
Timeclock
– the valve turns on/off at the times set for the valve3 timeclock in the Timers Menu (see
Operations Manual). The valve3 button can also be used to turn the valve output on or off.
Solar
– the valve operates when the filter pump is running and solar heat is available and the water is
less than the desired temperature setting. Solar heating must be enabled in the “Solar Config. menu
for proper operation to occur.
In-Floor Cleaner
– the valve switches the water returning to the pool between the in-floor cleaner and
the normal return jets which facilitate efficient surface skimming. The valve will operate the in-floor
cleaner for the first half of each clock hour and then switch to the jets/skimming for the last half of the
hour.
