Hasselblad 503CWD User Manual Download Page 61

Page: 61 / 82

• The

Exposure Cable EL

(supplied) should be connected.

• Only the single shot function (A or AS mode camera settings) should be set on the camera.

Rapid sequence shots are not possible.

• Use the

Adapter EL

(supplied) to provide the necesssary extension beyond the motor hous-

ing of the EL models for battery attachment. It is attached to the 503CWD digital back in

the same manner as a battery, and the battery itself is then attached to the adapter as in

the illustration.

ELX

For use with 500EL/ELM and 500/553ELX models:

• Make an

ELX

setting.

• The

Exposure Cable EL

(supplied) should be connected.

• All exposures times, including the B setting, function correctly without having to alter

the “Exposure Time” setting.

• Rapid sequence shots are not possible.
• Use the

Adapter EL

(supplied) to provide the necesssary extension beyond the motor hous-

ing of the EL models for battery attachment. It is attached to the 503CWD digital back in

the same manner as a battery, and the battery itself is then attached to the adapter as in

the illustration.

Pinhole

For use with lenses/cameras with no shutter. Intended primarily for use in a studio envi-

ronment where complete darkness can be achieved and exposures made accordingly (also

useful for ‘light painting’). In this mode the 503CWD digital back uses the exposure time

(as well as other required stages in a capture sequence) set in the Capture Sequence dialog.

The back can be triggered either via the

START

(MENU/EXIT) button or from FlexColor

(see later section for full description of Capture Sequence settings procedure).

Flash sync

For use with non-modiﬁed 200 series models (together with C-lenses in C-mode), an

ArcBody, a FlexBody or view cameras with a Hasselblad adapter.

• Make a

Flash sync

setting.

• A

Flash sync input cable

should not be used.

• All exposures times, including the B setting, function correctly without having to alter

the “Exposure Time” setting.

• Do not use a winder at rapid sequence setting.

SWC

For use with 903 SWC and 905 SWC models.

• Make an

SWC

setting.

PLEASE NOTE: Due to the mechanical design of the SWC, pressing the exposure release button
too slowly may cause a faulty capture with a magenta cast. Either press the button much more
distinctly or alternatively change the setting from

SWC

Flash sync

and use the flash sync

cable to connect the lens to the digital back.

200

For use with modiﬁed 202, 203 and 205 models together with F-lenses or CF-lenses

in F-mode. (Only these three models can be modiﬁed for cable-free compatibility

with the 503CWD digital back. Please contact your Hasselblad dealer for further

information)

• Make a

200

setting.

• A

Flash sync input cable

should not be used.

• All exposures times, including the B setting, function correctly without having to alter

the “Exposure Time” setting.

• Do not use a winder at rapid sequence setting.

All Hasselblad EL models

All Hasselblad EL models except ELD

Adapter EL

Exposure Cable EL

Summary of Contents for 503CWD



















































































Search results

Summary of Contents for 503CWD

Reviews:

Related manuals for 503CWD

Brands by name

Popular brands

Hasselblad 503CWD, User Manual

Search results

Summary of Contents for 503CWD

Reviews:

Related manuals for 503CWD

Brands by name

Popular brands