FAX 5/10/20/30/40KW
October 28, 2013
2
‐
3
888
‐
2720
‐
001
WARNING:
Disconnect
primary
power
prior
to
servicing.
Copyright
©2013,
Harris
Broadcast
2.6
Installation
Note
It should be noted that any remote control, status or analog meter connections be made only after the
transmitter has been initially turned on and operation verified.
This
transmitter
installation
section
provides
instructions
on
proper
cabinet
placement,
inter
‐
cabinet
wiring
where
applicable,
grounding,
AC
power
connections,
RF
out
connection,
and
static
checks
required
before
application
of
AC
power.
The
later
part
of
the
installation
process
involves
the
initial
turn
‐
on
procedure
and
initial
equipment
checks
to
assure
proper
operation.
Note
All connections referred to in this installation procedure should be verified using the schematic diagrams
supplied with the transmitter. The schematic diagrams should be considered the most accurate docu-
ment in case of a discrepancy.
2.6.1
Remove Shipping Materials
In
preparation
to
remove
the
cabinets
from
the
shipping
skids,
it
may
be
necessary
to
remove
any
tape,
foam,
and
supports
used
for
shipping.
Remove
these
materials
at
this
time.
The
base
of
the
cabinet
may
be
bolted
to
a
skid
in
the
two
front
corners
and
the
two
rear
corners
with
carriage
bolts,
flat
washers,
lock
washers,
and
nuts.
When
it
is
desired
to
remove
the
cabinets
from
the
skids,
remove
this
hardware.
A
socket
wrench,
a
short
extension,
and
a
9/16
‐
inch
deep
‐
socket
are
required.
2.6.2
Setting Transmitter in Place
If
your
transmitter
is
a
FAX30/40
and
was
shipped
with
the
cabinets
split,
it
will
be
necessary
to
re
‐
assemble
the
cabinets.
The
instructions
for
cabinet
re
‐
assembly
are
located
in
Appendix
a
of
this
manual.
Complete
the
procedure
prior
to
continuing
with
this
section.
Prior
to
removing
the
bolts,
move
the
transmitter
as
close
as
possible
to
the
final
location.
Once
the
bolts
are
remove
the
transmitter
cabinet
can
be
taken
off
the
skid
and
be
set
into
its
final
position.
See
Section
1
‐
11
of
this
manual
for
site
selection
information.
•
Carefully
inspect
the
transmitter
for
loose
hardware,
loose
or
unconnected
wires,
and
any
debris
in
the
rack
•
Level
the
cabinets
•
Secure
rack
to
the
floor
and
neighboring
racks
if
required
•
Install
all
power
amplifier
modules
in
the
location
per
the
factory
test
data.
This
can
be
found
on
page
3
under
"PA
Serial
Number
Assignments".
This
step,
while
not
necessary,
helps
to
ensure
the
transmitter
performs
as
close
as
possible
as
in
the
factory
test.
See
Figure
2
‐
1
for
slot
locations
in
the
power
block.
•
Install
all
power
supply
modules.
These
can
be
installed
in
any
location.
Summary of Contents for Flexiva FAX 10KW
Page 2: ......
Page 8: ......
Page 10: ...WARNING Disconnect primary power prior to servicing ...
Page 167: ......
