Harman Accentra Installation & Operating Manual Download Page 44

44

3-90-00674R20_08/12

Addendum

minimizing Smoke during loss of Power using battery back-up 

harman

TM

 strongly recommends installing battery back-up to minimize entry of smoke into the 

room in the event of power loss.

Your pellet/biomass burning appliance relies on a combustion blower to remove exhaust. A power failure 

will cause the combustion blower to stop. This may lead to exhaust seeping into the room. Vertical rise in 

the venting may provide natural draft. It is, however, no guarantee against leakage.

There are two harman

TM

 approved battery back-up options for your appliance: 

uninterruptible Power Supply (uPS)

 UPS battery back-ups are available online or at computer and 

office equipment stores.  Your Harman

TM

 appliance with Rev E or later software available beginning in 

November 2010 may be plugged directly into a Harman

TM

 approved UPS: 

  The 

APC (American Power Conversion) model #BE750G 

and the

 TrippLite model 

INTERNET750U

 are tested and approved.  Other brands or models may not be compatible. 

When power is lost, a fully charged UPS will power a safe, combustion blower only shut-down.  Your 
appliance will pulse the blower every few seconds to clear exhaust until the fire is out.  

NOTE: The uPS 

provides safe shut-down only. It is not intended for continued operation. 

Your appliance will recognize when power is restored. What happens depends on ESP temperature and 
whether it is equipped with automatic ignition: 

In “Automatic” setting

, units equipped with automatic ignition will respond to the set point and 

ESP temperature and resume normal operation. 

In “manual” setting

 or for units without automatic ignition: 

  If the ESP is cool, the appliance will remain shut down. 

  If the fire is out and the ESP is still warm, the feeder may restart. Since the fire is out, the 

ESP temperature will not rise. The unit will then shut-down, and may flash a six-blink status 
error. (

See ESP error codes)

  If the fire is still burning, it will resume normal operation.  

Contact your dealer if you have questions about UPS compatibility with your appliance. 

harman Surefire 512h battery back-up

 The 512H connects to a 12 volt deep cycle battery that will run 

your appliance for up to eight (8) hours. It includes a trickle charge feature that keeps your battery 
charged when power is available.  

NOTE: If the power is out for longer than battery life, smoke 

leakage may still occur unless your stove has been safely shut down. 

CAuTION! Always keep appliance doors and hopper lid closed and latched during 

operation and during power failures to minimize risk of smoke or burn-back. 

CAuTION!  use only harman

Tm 

approved battery back-up devices.  Other products may not 

operate properly, can create unsafe conditions or damage your appliance.

Power Failures / back-up Power

Summary of Contents for Accentra

















































Reviews: